• This Forum is for adults 18 years of age or over. By continuing to use this Forum you are confirming that you are 18 or older. No content shall be viewed by any person under 18 in California.

7-6.5PRCW

I heard something today I want to clear up. I guess at a match guys were saying you could buy my reamer from Brunos and not wait on JGS. I never gave my print to Brunos. I have no idea what reamer they are selling, even if they put a w on it.
 
Last edited:
Nvcnvc said:
Thanks for dies info guys....
Click to expand...
Eric really seems to have it wired and offers two different sizing die bases depending on what size your "200" mark is. .532" or .535" at the 200 line.
Stick with Eric's reamer version available from Manson or JGS's Alex Wheeler version and either one can be had as No Neck Turn or Neck Turn, virtually identical and I believe that perhaps they may even have collaborated on a cartridge that Mr Walker has done a lot to develop.
As for a seating die {Eric does not offer one} I bought a L E Wilson Micrometer seating blank die and used my reamer to bore it so that it matches my chamber {Wilson does not at this time offer a "ready made" one for the 7PRCC/7-6.5PRCW}
 
Last edited:
Thanks Fire Dog and everyone. I was leaning that direction myself. Although the SAC seating dies look appealing. Expensive though..
 
Fire Dog said:
Eric really seems to have it wired and offers two different sizing die bases depending on what size your "200" mark is. .532" or .535" at the 200 line.
Stick with Eric's reamer version available from Mason or PTG's Alex Walker version and either one can be had as No Neck Turn or Neck Turn, virtually identical and I believe that perhaps they may even have collaborated on a cartridge that Mr Walker has done a lot to develop.
As for a seating die {Eric does not offer one} I bought a L E Wilson Micrometer seating blank die and used my reamer to bore it so that it matches my chamber {Wilson does not at this time offer a "ready made" one for the 7PRCC/7-6.5PRCW}
Click to expand...
A word of warning, the .532 die is extremely tight - I tried mine on a virgin piece of brass which measured .530 at the .200 line and it stuck firmly in the die. I'll get it out this weekend with some much needed help, but advised Erik who was very helpful about the situation. He'll send me out a return label so I can send it back and get the .535 version which should be a better fit.
 
Last edited:
That’s very good info. Thanks. I am ordering the .535 version. I am going with the dimensions from Alex’s reamer at Jgs.
 
Fire Dog said:
Eric really seems to have it wired and offers two different sizing die bases depending on what size your "200" mark is. .532" or .535" at the 200 line.
Stick with Eric's reamer version available from Mason or PTG's Alex Walker version and either one can be had as No Neck Turn or Neck Turn, virtually identical and I believe that perhaps they may even have collaborated on a cartridge that Mr Walker has done a lot to develop.
As for a seating die {Eric does not offer one} I bought a L E Wilson Micrometer seating blank die and used my reamer to bore it so that it matches my chamber {Wilson does not at this time offer a "ready made" one for the 7PRCC/7-6.5PRCW}
Click to expand...
I assume your talking about me. I do not have any reamers available through PTG. Only JGS. I recommend JGS because thats who I use and am familiar with their grind angles and tolerances. If you take the print to someone else, thats on you. There was no collaboration on any reamers. At the time, Eriks was released it was just my reamer, but adjusted for a 1-30 lead angle. Dont know if anything has changed or not. Bullet central will be offering a seating die, if they already do not. I have just been reaming Wilson blanks as usual with anything we cant get off the shelf. Reports on Eriks dies have been good, but so are reports on IN SPEC Bullet central dies. The base on the BC die is speced under .530". I have even gotten good feedback on the Redding dies. The problem is not the in spec dies. Its the out of spec dies.
 
Alex Wheeler said:
I assume your talking about me. I do not have any reamers available through PTG. Only JGS. I recommend JGS because thats who I use and am familiar with their grind angles and tolerances. If you take the print to someone else, thats on you. There was no collaboration on any reamers. At the time, Eriks was released it was just my reamer, but adjusted for a 1-30 lead angle. Dont know if anything has changed or not. Bullet central will be offering a seating die, if they already do not. I have just been reaming Wilson blanks as usual with anything we cant get off the shelf. Reports on Eriks dies have been good, but so are reports on IN SPEC Bullet central dies. The base on the BC die is speced under .530". I have even gotten good feedback on the Redding dies. The problem is not the in spec dies. Its the out of spec dies.
Click to expand...
MY BAD... {:~(
Yes, I was referring to you and I did get crossed wires about the reamer manufacture and have amended my post... Just a mental block as I have reamers from all three companies.
JGS is what I meant to put in....
My apologies Mr Wheeler.
 
Last edited:
Alex Wheeler said:
I assume your talking about me. I do not have any reamers available through PTG. Only JGS. I recommend JGS because thats who I use and am familiar with their grind angles and tolerances. If you take the print to someone else, thats on you. There was no collaboration on any reamers. At the time, Eriks was released it was just my reamer, but adjusted for a 1-30 lead angle. Dont know if anything has changed or not. Bullet central will be offering a seating die, if they already do not. I have just been reaming Wilson blanks as usual with anything we cant get off the shelf. Reports on Eriks dies have been good, but so are reports on IN SPEC Bullet central dies. The base on the BC die is speced under .530". I have even gotten good feedback on the Redding dies. The problem is not the in spec dies. Its the out of spec dies.
Click to expand...
I must have gotten received one which is out of spec then as mine only sizes down to .532. It's pretty good, but I'd love it if it went down to .531 or .530.

Not sure what Erik's .532 die sizes down to but it's enough to result in stuck cases so I'm interested to know what his .535 die sizes down to.
 
Last edited:
Willow said:
I must have gotten a "dud" then, mine only sizes down to .532. It's pretty good, but I'd love it if it went down to .531.

Not sure what Erik's .532 die sizes down to but it's enough to result in stuck cases so I'm interested to know what his .535 die sizes down to.
Click to expand...
What are you using for case lube?
Have you tried this?
 
You must log in or register to reply here.

Upgrades & Donations

This Forum's expenses are primarily paid by member contributions. You can upgrade your Forum membership in seconds. Gold and Silver members get unlimited FREE classifieds for one year. Gold members can upload custom avatars.


Click Upgrade Membership Button ABOVE to get Gold or Silver Status.

You can also donate any amount, large or small, with the button below. Include your Forum Name in the PayPal Notes field.


To DONATE by CHECK, or make a recurring donation, CLICK HERE to learn how.

Classified Ads

Forum statistics

Threads
165,806
Messages
2,203,766
Members
79,130
Latest member
Jsawyer09

Share This Page

Back
Top