• This Forum is for adults 18 years of age or over. By continuing to use this Forum you are confirming that you are 18 or older. No content shall be viewed by any person under 18 in California.

Pls any ideas on how to mount a scope on a Feinwerkbau 2600 - Think it has +-12mm dovetails

tothemax

Silver $$ Contributor
Hi,

Am looking for viable options to mount a scope on a Feinwerkbau 2600 - Think it has +-12mm dovetails

Would anyone know either 30 mm scope rings, a Picatinny rail or some other adapter to mount a scope on the Feinwerkbau 2600.

Any ideas on where I could get something that would work? One with a 20 MOA option to shoot at 200 yards would be great

Much appreciate and and all advice

Tnx
 
Last edited:
Most European rifles are 11 mm, never heard of 12 mm. Check Champions Choice web
site for rings/mounts for your rifle. There are lots of good rings in 30mm including Harrells,
which I use and like.
Regards,

Joe McNeill
SW Arkansas
 
Have you tried calling Champions Choice and asking. They handle Feinwerkbau (both air and smallbore), so they may have an idea.

Good luck,

Dave

Must be good advice, two minds, all that
 
yes Joe is correct almost always 11mm be sure to double check. If 11 there are lots of options like Talley

rimfire-and-specialty-rings

and area 419

www.area419.com

Anschutz 1761 Scope Base

Following the success of our CZ455 and 457 scope bases, it only made sense for us to begin to roll out bases for Anschutz rifles. This design, made from a single piece of T7075 aluminum and machined in house on our Haas VF4SS 4 axis machining center is designed to slide onto the dovetail and [...]
www.area419.com www.area419.com

Just to name a couple
 
There shouldn't be an issue using BKL ring mounts. I use them on my Feinwerkbau 300. Perfect fit, BTW 11mm rails
 
Thank you and much appreciate the advice.

https://www.ebay.com/itm/334198181730?epid=727397744&hash=item4dcfc38f62:g:cU8AAOSwBtNfUPQH

Here are pics of a possible option on the FWB adapter I found on EBAY and the FWB dovetails
51660500518_88fce201dd_b.jpg


51660946609_a804d034f9_b.jpg


51660268376_145c610b83_b.jpg
 
Last edited:
243Lapua said:
There shouldn't be an issue using BKL ring mounts. I use them on my Feinwerkbau 300. Perfect fit, BTW 11mm rails
Click to expand...

Wow great options there... this may be the ticket... Also I love their pic rail options !

BKL Technologies - Dovetail to Weaver Picatinny Adaptor Mounts - Made In The USA

The 500 series from BKL - Dovetail to Weaver/Picatinny Adaptor Mounts. Red Dot Scope Adaptors designed to accept all weaver-style scope mounts. Mounts to 3/8-in or 11mm dovetails.
www.bkltech.com

Specially these where I can use pic rings. Looks like this will be the ticket... Iooks it can spread wide enough to fit on the wider FWB dovetails.. I will call them on Monday to verify. Thank you so much.. exactly the option I was looking for

www.bkltech.com

BKL-566 - Dovetail to Weaver Adaptor Mounts - BKLTech.com

Accepts Weaver-style mounts. Ideal for Red Dot scope mount.
www.bkltech.com
 
This are my BKL mounts on my Anschutz rail. I have the same model rings on my Feinwerkbau. You can see that BKL has a threaded side to insert a screw maybe even the clamping screw to open up a bit the mount. I hope that picture helps. But a call to BKL will clear up a lot of things most of the time.
 

Attachments

  • 20211106_221814.jpg
    20211106_221814.jpg
    342.9 KB · Views: 22
  • 20211106_221830.jpg
    20211106_221830.jpg
    346 KB · Views: 22
tothemax said:
Thank you and much appreciate the advice.

https://www.ebay.com/itm/334198181730?epid=727397744&hash=item4dcfc38f62:g:cU8AAOSwBtNfUPQH

Here are pics of a possible option on the FWB adapter I found on EBAY and the FWB dovetails
51660500518_88fce201dd_b.jpg


51660946609_a804d034f9_b.jpg


51660268376_145c610b83_b.jpg
Click to expand...
What you found are called riser blocks and are used for raising the front and rear metallic sights for better head / eye position.

They are for 11mm dovetails on FWB and many other EU rifles.

Not being certain of your planned use, I would highly recommend the following rail:


The rail will allow extended fore and aft movement of the scope for proper eye relief.

As for rings, I use Kelbly almost exclusively.
 
243Lapua said:
This are my BKL mounts on my Anschutz rail. I have the same model rings on my Feinwerkbau. You can see that BKL has a threaded side to insert a screw maybe even the clamping screw to open up a bit the mount. I hope that picture helps. But a call to BKL will clear up a lot of things most of the time.
Click to expand...
1813benny said:
What you found are called riser blocks and are used for raising the front and rear metallic sights for better head / eye position.

They are for 11mm dovetails on FWB and many other EU rifles.

Not being certain of your planned use, I would highly recommend the following rail:


The rail will allow extended fore and aft movement of the scope for proper eye relief.

As for rings, I use Kelbly almost exclusively.
Click to expand...
Thank you much,

Much appreciate the great advice. Will look into these great options for sure.
 
tothemax said:
Thank you and much appreciate the advice.

https://www.ebay.com/itm/334198181730?epid=727397744&hash=item4dcfc38f62:g:cU8AAOSwBtNfUPQH

Here are pics of a possible option on the FWB adapter I found on EBAY and the FWB dovetails

51660268376_145c610b83_b.jpg
Click to expand...
Those aren't adaptors for mounting standard rings/sights on the rail. Those are raiser blocks, wedges to lift up the aperture sights: big block under the rearsight, small block under the front. 3P (and prone only) shooters use so they don't strainer cramp their neck to aim.
 
tothemax said:
Thank you much,

Much appreciate the great advice. Will look into these great options for sure.
Click to expand...
The BKL dovetail to Weaver adapters (500 series)should work as they can expand the clamping width by removing the clamping screws and screwing them into the provided threaded holes. by tightening the screws they will push the clamping slot further apart and make it wider. I would think making them 1-mm (0.039) wider would be no problem.

Lee
 
BKL rings directly on the 11mm dovetail on my TX200 works fine. Go to the air gun forums with European participation. They are really big into them.
 
butchlambert said:
Buy Kelbly RF rings. I have them on my Walther KK300 and my Anschutz 1913. Very reasonable.
www.kelbly.com

30mm Scope Rings - Dovetail - Kelbly Rifles

Video Ring Dimensions
www.kelbly.com
Why spend money on a rail?
Click to expand...
I like rails for rimfire because they can provide 20 MOA of adjustment to shoot at 200 years and beyond.. also I am too cheap to buy many expensive scopes so I swap out the couple I have from one rifle to the next.... am not like your high dollar guys LOL
 
tothemax said:
I like rails for rimfire because they can provide 20 MOA of adjustment to shoot at 200 years and beyond.. also I am too cheap to buy many expensive scopes so I swap out the couple I have from one rifle to the next.... am not like your high dollar guys LOL
Click to expand...
High dollar? Kelbly's rings with the 25moa are probably better and maybe cheaper if cheap is part of it.
https://www.kelbly.com/product/34mm-rings-picatinny/
Those are 30mm.
 
You must log in or register to reply here.

Upgrades & Donations

This Forum's expenses are primarily paid by member contributions. You can upgrade your Forum membership in seconds. Gold and Silver members get unlimited FREE classifieds for one year. Gold members can upload custom avatars.


Click Upgrade Membership Button ABOVE to get Gold or Silver Status.

You can also donate any amount, large or small, with the button below. Include your Forum Name in the PayPal Notes field.


To DONATE by CHECK, or make a recurring donation, CLICK HERE to learn how.

Classified Ads

Forum statistics

Threads
165,061
Messages
2,188,943
Members
78,679
Latest member
Janusz

Share This Page

Back
Top