Anyone reloading 10mm

[padom]

Ive been loading 10mm for both my G40 BarSto and Dan Wesson Bruin. I love my 10mm

I load a lot of W572 and Longshot and both are excellent. Ive been shoot lots of 200gr MBW WFN-GC and WFN-PB..

Dan Wesson Bruin
8gr Longshot
200gr MBW WFN-PB
New factory primed SIG brass
1228 SD 1.5 ES 4 over 10 shots

For Comparison
Underwood 200gr HC on same day out of same gun
1210 SD 11 ES 33 10 shots


Glock 40 BarSto Match Custom Fit Barrel
8gr Longshot
200gr MBW WFN-PB
New factory primed SIG brass
1240 SD 8 ES 20 over 10 shots

For Comparison
Underwood 200gr HC on same day out of same gun
1223 SD 21 ES 53 10 shots

My other go to load

Glock 40 BarSto Match Custom Fit Barrel
7.2gr W572
200gr MBW WFN-PB
New factory primed SIG brass
1211 SD 9 ES 31 over 10 shots

Dan Wesson Bruin
7.6gr W572
200gr SIG V-Crown JHP (Sierra)
New factory primed SIG brass
1251 SD 2 ES 6 over 10 shots

https://imgur.com/xNmasmc

https://imgur.com/MKdVAv9

https://imgur.com/BPwYfUG

https://imgur.com/vApft23

https://imgur.com/neKMPVq

 

[padom]

N350 is also a very very accurate powder with the MBW PB and GC bullets. Just slower than your high powered loads with AA9, Longshot, W572

 

[padom]

For those wondering, after having long conversations with great people at MBW.. They told me to find a load for their 200gr HC WFN-GC in the 1100-1200 range that you can control and shoot accurately and it will penetrate...

 

[46and2]

Ive been loading 10mm for both my G40 BarSto and Dan Wesson Bruin. I love my 10mm

I load a lot of W572 and Longshot and both are excellent. Ive been shoot lots of 200gr MBW WFN-GC and WFN-PB..

Dan Wesson Bruin
8gr Longshot
200gr MBW WFN-PB
New factory primed SIG brass
1228 SD 1.5 ES 4 over 10 shots

For Comparison
Underwood 200gr HC on same day out of same gun
1210 SD 11 ES 33 10 shots


Glock 40 BarSto Match Custom Fit Barrel
8gr Longshot
200gr MBW WFN-PB
New factory primed SIG brass
1240 SD 8 ES 20 over 10 shots

For Comparison
Underwood 200gr HC on same day out of same gun
1223 SD 21 ES 53 10 shots

My other go to load

Glock 40 BarSto Match Custom Fit Barrel
7.2gr W572
200gr MBW WFN-PB
New factory primed SIG brass
1211 SD 9 ES 31 over 10 shots

Dan Wesson Bruin
7.6gr W572
200gr SIG V-Crown JHP (Sierra)
New factory primed SIG brass
1251 SD 2 ES 6 over 10 shots

https://imgur.com/xNmasmc

https://imgur.com/MKdVAv9

https://imgur.com/BPwYfUG

https://imgur.com/vApft23

https://imgur.com/neKMPVq

Do you guys get a lot of lead fouling with those Montana bullets?

 

[padom]

THere a little bit in the barrel if you shoot a bunch of them in a range session. But I was told to shoot a jacketed bullet every once in a while during your range session to clean it out and it works great. Ill shoot a JHP or 2 every mag or two and cleans it right out.

 

[wboggs]

Probably good advice.


41

As a .41 mag shooter also, a 210 cast at 1300 will do ta superior job.
No reason to push it to 1500 with max loads. Sometimes people focus on paper ballistics too much

 

[Mulligan]

Do you guys get a lot of lead fouling with those Montana bullets?

I do not.
I clean after a range session, and look with the bore scope, no issue.
CW

 

[41rem]

For those wondering, after having long conversations with great people at MBW.. They told me to find a load for their 200gr HC WFN-GC in the 1100-1200 range that you can control and shoot accurately and it will penetrate...

No doubt on that statement, I believe I watched a gel test & it penetrated 2 full blocks.

41

 

[justinp61]

Do you guys get a lot of lead fouling with those Montana bullets?

Virtually none. I think the brass gas check takes care of it.

 

[Alex Wheeler]

Do you guys get a lot of lead fouling with those Montana bullets?

I never have had any leading in 5 or 6 revolvers and a few rifles

 

[lb-ft]

Anyone use WSF for their 10mm loads?

 

[ROBARRC50]

Noticed quite a few of you are using similar loads to me, have you guys upgraded your recoil springs to a higher weight over the factory one?

I went with a 20 lb, to tighten up my ES.

41

I am at 24 lbs now i was running a 22 lbs but the frame was still getting battered at 1200fps in a g20 4.6 barrel length. 24 seems better more controlled ejection or consistent in where it lands. Have 300 rounds fired with the 24 pound spring no hiccups yet. I fired 500 rounds at 22 pounds with no hiccups.

 

[41rem]

I am at 24 lbs now i was running a 22 lbs but the frame was still getting battered at 1200fps in a g20 4.6 barrel length. 24 seems better more controlled ejection or consistent in where it lands. Have 300 rounds fired with the 24 pound spring no hiccups yet. I fired 500 rounds at 22 pounds with no hiccups.

Where would a guy check for battering & you using the factory Glock barrel?

 

[ROBARRC50]

Where would a guy check for battering & you using the factory Glock barrel?

Used factory glock and now onto a kkm barrel. Glock barrel kinda killed brass at that velocity. Was having sizing isues also with brass getting a line where it bulged when sized towards the case head . Like the brass was getting pushed over some. I have a grx die ariving tomorrow. To see if that will help with that issue. Should know next week. With that test.

 

[jrbirdie]

I enjoy my 610s for anything I try to from lead hard cast to JHP. I just bought a M&P 2.0 also in 10mm. Blue dot and power pistol is all I use, works great with every bullet

 

[Hickok]

My Glock 20 is a Gen 4, shooting 180 lee Cast @ 1300 fps with Bluedot. Cases are nice and smooth, no "Glock Smiley faces"!

 

[41rem]

I need a set of carbide 10mm dies with taper crimp if anyone has an extra laying around.

Post or PM

41

 

[41rem]

I need a set of carbide 10mm dies with taper crimp if anyone has an extra laying around.

Post or PM

41

Found a nice used RCBS set, should be here soon. I'll see if this factory Glock G20 barrel will allow me to run the loads I want.

As an aside, anyone ever load the Hornady 155 grain XTP bullets?


41

 

[Hoser]

The biggest tip I can offer...

It is a 10mm Auto. Not a 41 Mag auto. 180s and 200s seem to be the sweet spot for pressure, velocity and accuracy.

 

[Richard Jones]

Changed the MS from 18.5# to 21#. Changed RS from 23# to 16#. I've used Silhouette, Power Pistol, 800X, Longshot, W231, N350, CFE Pistol, AA #5. All with 180 FMJ Delta Precision or 180 RNFP from Blue Bullets. I run a shok buff occasionally, but it requires a shorter MS in order to cycle. SA Ronin.