• This Forum is for adults 18 years of age or over. By continuing to use this Forum you are confirming that you are 18 or older. No content shall be viewed by any person under 18 in California.

250gr A Tip in a 308

adam said:
Looks like bugholes has some 8tw 308 barrels in stock:
www.bugholes.com

Bartlein 30 cal 8 twist SS Heavy Varmint 31''

www.bugholes.com
www.bugholes.com

Bartlein 30 cal 8 twist SS Heavy Palma 31''

www.bugholes.com

FWIW I used to shoot a 7mm wildcat based on the wssm case and shot 195 bergers at about 2450. Most accurate gun I've ever had. The excess drop was inconvenient for PRS, but I still placed well in matches with it. From my experience, shooting heavy bullets with low velocity and a long freebore is not only viable, but produces excellent results.
Click to expand...

Adam, man, thank you! I didn’t even know Bartlein had an online inventory to select from.
 
Oh yes, I see that now. I’ll be calling down one of those to this project.

Edit: Online order just submitted for heavy varmint, 31”.
 
Last edited:
That barrel ^^ will debut at Bayou Sunday for the 1,000 yard club match with an even longer free bore than the earlier pictured rifle, to allow testing of both 48 and 49 grains of powder. Probably 2 relays, with a relay reserved to test my planned state rsaum barrel with 190 A-Tips.

On the left is the fill level of 48.0 grains while the right is 49.0. The powder is H4350. There’s simply no getting around load compression when this much powder is being used. The barrel hasn’t been finished or tested at this point but I would expect velocity from it at well over 2,500 FPS, and will stick to CCI 41 mil spec primers exclusively.

It’s very easy to discern in the picture where exactly the bullet is seated in the neck, and that is slightly shallower than my other rifle permits, increasing the case capacity. It ought to be perfectly extractable but let’s hope that doesn’t get often tested

This barrel will be on a conventional F/TR XIT -Phoenix bipod set up.

1616985663836.jpeg

In the meantime I prepped two new barrels to shoot the 90’s, Bergers so far and now I do have some .22 A-Tips to load up.
 
Last edited:
... “he likes it, he likes it.”

I’m showing that at 2,500 FPS, the 250 A-Tip drifts the identical 5.0 moa that a 184 hybrid drifts at 1,000, if your velocity is 2,975, an area of the short magnums and beyond what a .284 can propel them to.

I think that real world drift will be backed up in that the .308 retained energy on target at 1,000 is actually significantly greater than the 7 magnums.

Compared to the WSM with a Berger 215, the nominal 10 mph drift is equal at 1,000, if you shoot the 215 at 2,960.
 
Last edited:
If it works, I’ll be very curious how long the rules will permit a .308 loaded round that shoots inside almost all open cartridges and needs a .338 LM seating die, to continue.

Someone needs to neck down the .338 LM and shoot these out of it. Their BC is actually higher that the 300 grain A-Tip, a fact which was a little discouraging to me as a large amount of my h-1000 sits in loaded .338 cases right now.
 
... It’s a fine line between those two, but Hornady made this Red Pill, and there’s no choice but to see how deep the rabbit hole goes.
 

Attachments

  • 472B503B-D5F0-4FE8-9201-7C43ED41503F.jpeg
    472B503B-D5F0-4FE8-9201-7C43ED41503F.jpeg
    28.3 KB · Views: 23
  • 7916A378-8446-40F2-83A0-7B40115B86EB.jpeg
    7916A378-8446-40F2-83A0-7B40115B86EB.jpeg
    246.9 KB · Views: 22
davidjoe said:
That barrel ^^ will debut at Bayou Sunday for the 1,000 yard club match with an even longer free bore than the earlier pictured rifle, to allow testing of both 48 and 49 grains of powder. Probably 2 relays, with a relay reserved to test my planned state rsaum barrel with 190 A-Tips.

On the left is the fill level of 48.0 grains while the right is 49.0. The powder is H4350. There’s simply no getting around load compression when this much powder is being used. The barrel hasn’t been finished or tested at this point but I would expect velocity from it at well over 2,500 FPS, and will stick to CCI 41 mil spec primers exclusively.

It’s very easy to discern in the picture where exactly the bullet is seated in the neck, and that is slightly shallower than my other rifle permits, increasing the case capacity. It ought to be perfectly extractable but let’s hope that doesn’t get often tested

This barrel will be on a conventional F/TR XIT -Phoenix bipod set up.

View attachment 1245391

In the meantime I prepped two new barrels to shoot the 90’s, Bergers so far and now I do have some .22 A-Tips to load up.
Click to expand...
Quick Load shows 70K+ PSI with that load o_O We're going squad you with the alligator!
 
Early on up above, there’s a post about the test load of 50.0 grains of RE 17, which is where the primer fell out of the brass with these bullets, in my original rifle. (Needed to work up to pin point where it is to stay well away from).

I’d be curious what the pressure shows to be, there, Doug?

I’m looking to have the new rifle tomorrow and work up loads.

Edit, ^ nice, finally, I was starting to think it wasn’t a real “Bayou” range.
 
Last edited:
You must log in or register to reply here.

Upgrades & Donations

This Forum's expenses are primarily paid by member contributions. You can upgrade your Forum membership in seconds. Gold and Silver members get unlimited FREE classifieds for one year. Gold members can upload custom avatars.


Click Upgrade Membership Button ABOVE to get Gold or Silver Status.

You can also donate any amount, large or small, with the button below. Include your Forum Name in the PayPal Notes field.


To DONATE by CHECK, or make a recurring donation, CLICK HERE to learn how.

Classified Ads

Forum statistics

Threads
165,800
Messages
2,203,290
Members
79,110
Latest member
miles813

Share This Page

Back
Top