Reattaching Remington Bolt Handle, timing.

[jackieschmidt]

A friend needs a Remington bolt handle reattached and timed to the action. Who is best recommended for this.?

 

[Savagenut71]

Accu-tig.com

 

[Walt Krafft]

LRI has done great work for me.

 

[Dead Eye]

Is Accu-tig still in business? I sent emails and never received a reply back.

 

[Bill Rodolph]

I used LRI earlier this year. Did good work, but don't be in a hurry. Mine tool close to 5 months.

 

[Mulligan]

Welcome to Accu-TIG

A few years ago, I posted the same question.
Dan came highly recommended, so I contacted him and shipped it off per his instructions. It was back at the house quickly and a job well done.

I have no knowledge of anyone else that provides this service.
CW

 

[DaveTooley]

Last I heard Dan was offsite working. I guess he hasn't returned.
Butch Lambert stayed in touch with him but Butch is laid up after emergency neck surgery.

 

[Kracken McGraw]

Jackie you might ask Mike Bryant if he has sent anything to Dan to be worked on lately.
I think on Butch’s last post about Dan, he said he was enjoying a lot of hunting and fishing and being pretty selective on his clients.

 

[jackieschmidt]

I might just do it myself. It’s for Geramo, he said he would be fine with it bolted on rather than sil brazed. I have bolted on several Farley handles with goos success.

 

[slobhunter2]

I might just do it myself. It’s for Geramo, he said he would be fine with it bolted on rather than sil brazed. I have bolted on several Farley handles with goos success.

Please do, and post a lot of pics.

 

[okie]

Last I heard Dan was offsite working. I guess he hasn't returned.
Butch Lambert stayed in touch with him but Butch is laid up after emergency neck surgery.

Dave, You do that right??

 

[DaveTooley]

Dave, You do that right??

Neck surgery?
Not me

 

[okie]

Neck surgery?
Not me

lol, no- the bolt timing

 

[jackieschmidt]

Please do, and post a lot of pics.

Here is how I did it.
I aligned the bolt on the action with the cocking piece dead center on the helix cocking path in the bolt body. I locked it in place against the action body abutments.
Using 5000 psi LocTite epoxy, I then attached the handle in place with it against the bolt handle stop and with a .010 shim between the extraction ramp and the action body, insuring maximum primary extraction.
I then put the bolt in my Mill and drilled and tapped two 8-40 screws to secure the handle.
The epoxy held it in place just fine during the drilling and tapping.

 

[LVLAaron]

LRI is working on bolt handle replacements:

 

[slobhunter2]

@jackieschmidt
Thanks for taking the time to post the pics and write up, I appreciate it.

 

[Silo1616]

View attachment 1709681Here is how I did it.
I aligned the bolt on the action with the cocking piece dead center on the helix cocking path in the bolt body. I locked it in place against the action body abutments.
Using 5000 psi LocTite epoxy, I then attached the handle in place with it against the bolt handle stop and with a .010 shim between the extraction ramp and the action body, insuring maximum primary extraction.
I then put the bolt in my Mill and drilled and tapped two 8-40 screws to secure the handle.
The epoxy held it in place just fine during the drilling and tapping.
View attachment 1709678View attachment 1709677

My butt would have been puckered worried about the epoxy releasing from the drilling heat. Good job!

 

[jackieschmidt]

My butt would have been puckered worried about the epoxy releasing from the drilling heat. Good job!

This is what I used to attach the bolt handle in the correct position. It has about a 30 minute seat time. We use it to mount non metallic bearings in Rudder Tubes and Propeller Shaft bearings in Push Boats.

I really wasn’t sure if it would work, but it did, and held the handle in place during drilling and tapping.