Do you clean brass every loading?

[Pawnee Bill]

Recently I have read some people saying they don’t clean brass every time they reload. Is this common? How often do you clean brass?

Thanks.

Yes. Clean brass is happy brass!

 

[Dgd6mm]

I didn't know you were supposed to clean it.

 

[rkittine]

I clean my brass after every firing. How depends what caliber / firearm. I do not spend as much time on Pistol Brass as I do on Rifle and even less on shotgun hulls.

 

[Longtrain]

Yup, anneal and clean with SS pins, each time. Not only do they shoot good, they look fabulous.

 

[tygranch]

I tumble every time. Clean primer pockets on match ammo every time also.

 

[ARW]

I don't remember the last time I washed my truck but after every firing I tumble (clean) the crap out of my brass.

 

[Homerange]

Yep, clean the primer pocket and if necessary deburr the flash hole, end of the case (trim) and neck chamfer but nutthing else. So some bits are bright and shiny clean.
YMMV.

 

[Shooter13]

Anyone remember "never dull"? I use it on the case necks on BR guns to clean the residue off, brush the necks and load. If the reload count is high (# of pieces of brass) I may tumble in media to get the resize lube off.

 

[sqrlgtr]

Anyone remember "never dull"? I use it on the case necks on BR guns to clean the residue off, brush the necks and load. If the reload count is high (# of pieces of brass) I may tumble in media to get the resize lube off.

same 4 me...

 

[D-4297]

Answers to this will vary and be Discipline specific , so there will be a very wide spectrum of information on this . As a F class competitor ; I fully clean my brass after every firing . Primer pockets , too . And anneal after every firing . The cost of custom dies , bushings , and even the brass itself warrant such labor , in my mind . And my bank account . Why would I want to spend nearly $200.00 for a custom F/L Bushing Die ; to jam a filthy case into it , coated with carbon , destroying the chance to have concentric , L/R Brass come out ? Damaging the ground and polished surfaces of the die and Bushings . When you consider the average F shooter fires around 2,500 to 3,000 rounds , or more a year , you'd have to have several custom dies sitting on the shelf , to facilitate such absurd waste of precision equipment . That's a lot of unnecessary abuse . Not to mention the amount of brass you would have to have on hand , at nearly a $1.00 per case . And how many rounds jammed into your $450 - $500 receiver and barrel sliding in and out , dragging that carbon across the surfaces , before you're complaining about not knowing if your chamber is going bad , or bolt lift issues , or you don't even know the cause of a myriad of problems . Just the tool & Diemaker in me , talkin here . Yep ! I'm severe OCD , but I got 5,600 rounds out of my last TR barrel . Go figger .

 

[bobm]

Clean? Never have, never will. Just primer pockets. The HP animal silhouette targets are big, I shoot offhand and score well.

RP 7mm-08 ....22x fired with 38.0 Varget and 130 SMK.

 

[6fatrat]

I will wipe them off if they are dirty, clean the primer pocket every time.

 

[Jason_A]

Bobm, now that’s some carbon build up lol.

 

[Ken]

Yep

 

[Shooter13]

Answers to this will vary and be Discipline specific , so there will be a very wide spectrum of information on this . As a F class competitor ; I fully clean my brass after every firing . Primer pockets , too . And anneal after every firing . The cost of custom dies , bushings , and even the brass itself warrant such labor , in my mind . And my bank account . Why would I want to spend nearly $200.00 for a custom F/L Bushing Die ; to jam a filthy case into it , coated with carbon , destroying the chance to have concentric , L/R Brass come out ? Damaging the ground and polished surfaces of the die and Bushings . When you consider the average F shooter fires around 2,500 to 3,000 rounds , or more a year , you'd have to have several custom dies sitting on the shelf , to facilitate such absurd waste of precision equipment . That's a lot of unnecessary abuse . Not to mention the amount of brass you would have to have on hand , at nearly a $1.00 per case . And how many rounds jammed into your $450 - $500 receiver and barrel sliding in and out , dragging that carbon across the surfaces , before you're complaining about not knowing if your chamber is going bad , or bolt lift issues , or you don't even know the cause of a myriad of problems . Just the tool & Diemaker in me , talkin here . Yep ! I'm severe OCD , but I got 5,600 rounds out of my last TR barrel . Go figger .

Every single piece of brass is hand cleaned before every putting in one of the custom dies! Good advise.

 

[centershot]

Step number one is to brush the inside of the neck. Wipe the necks off with a small rag with a bit of the same stuff with which I clean the bore. My reasoning for that step is that I don’t care to stick a cruddy neck into an expensive die. Then I lube the outside of the neck with Carmex Lip Balm and size the case and decap it. Then clean out the primer pocket and wipe the neck again.
I shoot bench rest only and we bench resters are an odd bunch.

I agree with your thinking about keeping the die from being scratched. Never heard of Carmex. Have to hit my wife up for some.

 

[eric n]

I used to clean them every time. Now I just wipe the necks and go on with sizing.
I’m not so sure it’s carbon on the necks after firing, it sure wipes off easy.

Wouldn’t embedded crap on the brass scratch your brass and not the hardened die?

 

[D-4297]

eric n ; Carbon is highly abrasive . If it will scratch brass , it will also scratch hardened Die steel . I made cold header dies for about five years , and they work by pushing a piece of clean , lubed brass wire cut-off into the die to form a small bolt or screw blank . Most dies had to be re-made after 10-15,000 blank runs . And they were carbide dies . Diamonds come from carbon under pressure , and carbide is formed from carbon with alloys and other things added .

 

[JMayo]

Bench rest only.
I clean the necks. Don't want that in my die.
Spray, size, wipeoff with paper towel,clean primer pocket then load em up.

 

[JFrank]

Yup, anneal and clean with SS pins, each time. Not only do they shoot good, they look fabulous.

There really should be an award or something for fellas that go that extra mile