7-6.5PRCW load data

[SDDasher]

I asked this on another thread, but I thought to ask again, if you all dont mind.
Can (should) one use ADG 7-6.5PRCW brass in wheeler .319NT chamber? I have a chance to buy a bunch of that brass at a very good price and I was wondering if there would be an issue. Thanks in advance

I use ADG brass with a .314 chamber W/O any issues running 2860ish using N555. The brass has been turned using an AutoDod. I shoot in temps ranging from 40-95+ degrees and had very few “clickers” with this brass in the two seasons of use. The same friend with the AutoDod also has a roll-sizer so I just borrow that if I need to.

 

[Nvcnvc]

thank you. I am trying to avoid turning necks. I read that ADG brass fits without turning in a .316 neck. Do you think that the fact that my neck is .319 will not make the neck expand too much? I hope I am asking my question correctly.

 

[gmr4]

I asked this on another thread, but I thought to ask again, if you all dont mind.
Can (should) one use ADG 7-6.5PRCW brass in wheeler .319NT chamber? I have a chance to buy a bunch of that brass at a very good price and I was wondering if there would be an issue. Thanks in advance

Yes.. you will not need to turn on a .319 and you may find the extra neck clearance is a good thing…

 

[Nvcnvc]

thank you

 

[Sandstorm]

I use it and it works real well..No issues here.

 

[BAT M 284]

Here's my load Data 55.9 Grains N555
180 Berger hybrid, lapua 6.5 Brass necked up to 7mm.seating on the lands.Muzzle velocity is 2860 .Redding S die 7 6.5prcw
Full length sizer.seating die Redding 7 saum competition . Redding. .309 tin bushing .Rifle is very accurate I shoot steel plate matches. I shot 4x6 steel plates consistently at 855 and 830
Yards.my Reamer is a Manson 7prcc.
All work was done by Joseph Jones at
Shaw Armament powder Springs Georgia.

 

[Blackrockcustom]

I build 2 one with a carbon six barrel 24" with a Weatherby 307 action. peak 44 stock, rem age tenon. I started load work up with 140 gr vld. 3 shot group .050" 3050 fps. next to load up 190 gr A-Tip.

second rifle is hells canyon armory barrel, rem 700 action, standard tenon thread, peak 44 stock.

Waiting on ADG to send more brass.

 

[806guns]

Any data on a 195 eol in a medium action 24" ?

 

[Willow]

Is anyone out there running Peterson 6.5PRC brass necked up at all? I've had very good success with Peterson 284 brass and just wondering whether their 6.5PRC brass stacks up to Lapua or ADG at all in terms of consistency/longevity?

 

[Sandstorm]

Im not a fan of Peterson Brass, but if your having success with it .. good for you.
I have had a miserable experience with it unless your Reamer is tooled for it. Good luck

 

[Willow]

Im not a fan of Peterson Brass, but if your having success with it .. good for you.
I have had a miserable experience with it unless your Reamer is tooled for it. Good luck

My 284 Shehane reamer was tooled for Peterson, so it's worked very well for me. Just haven't really heard much of anything as to whether their 6.5PRC brass is any good.

 

[JLT]

My 284 Shehane reamer was tooled for Peterson, so it's worked very well for me. Just haven't really heard much of anything as to whether their 6.5PRC brass is any good.

I have some but not enough experience with it to venture an opinion. I have 250 pieces, half of it once-fired and the other half is twice-fired. The twice-fired cases have a bit less capacity than Lapua, ~1.6 gr. less water capacity. They measured and weighed just fine, not altogether different from Lapua in terms of consistency, and my lot has thinner necks than Lapua. I turn to .3105" (.3150" neck) and the Peterson necks did not fully clean up at that measurement.

 

[Willow]

I have some but not enough experience with it to venture an opinion. I have 250 pieces, half of it once-fired and the other half is twice-fired. The twice-fired cases have a bit less capacity than Lapua, ~1.6 gr. less water capacity. They measured and weighed just fine, not altogether different from Lapua in terms of consistency, and my lot has thinner necks than Lapua. I turn to .3105" (.3150" neck) and the Peterson necks did not fully clean up at that measurement.

How does the .200 line stack up against Lapua out of the box and once fired?

 

[JLT]

How does the .200 line stack up against Lapua out of the box and once fired?

I don't recall, off hand. I will check my notes, measure a fired/resized case and report back shortly.

 

[323]

Is anyone out there running Peterson 6.5PRC brass necked up at all? I've had very good success with Peterson 284 brass and just wondering whether their 6.5PRC brass stacks up to Lapua or ADG at all in terms of consistency/longevity?

It’s all my one buddy uses for his 7 prcw. He sold all his adg 7 prcw to me. I’m too invested in ADG to switch.