Any thoughts? Anyone.I hear you. I'm leaning towards a .271" nk, .471" at the .200" mark, 1.555" chamber, 1.5 lead, .2440" dia.,and probably a .130" fb.
Any thoughts? Anyone.I hear you. I'm leaning towards a .271" nk, .471" at the .200" mark, 1.555" chamber, 1.5 lead, .2440" dia.,and probably a .130" fb.
I would go. 471 and match a harrells die. Mine are. 4708 and use a ring die to pull based down more. I'd go bigger, but got too many reamers to change. I make it work.What would you recommend ?
Depends on bullet.I hear you. I'm leaning towards a .271" nk, .471" at the .200" mark, 1.555" chamber, 1.5 lead, .2440" dia.,and probably a .130" fb.
Still haven't pulled the trigger on the reamer yet. After speaking to many people and coming up with what I think is a good design, I am going to send brass / dummy to the reamer manufacturer and check what I currently have working well and then adjust my final design based on the combination of information.
Depends on bullet.
I have searched the forums and I am still confused on the reamer I want for a 6 Dasher.
Shooting Alpha and Lapua Brass (both .2675 neck on loaded round) with berger 105 Hybrid.
They seem to run well in a range of anywhere from 10 - 30 off the lands currently
I think I have settled on a .2705 neck, .2433 free-bore diameter.
My confusion is in case length and throat / lead length and lead angle.
I see case lengths of 1.555 and 1.570 on a number of prints. All my cases would chamber in 1.555 without issue.
Does the maximum case length effect the free-bore length needed?
Would a 2 degree angle have any benefit over a 1.5?
First reamer I have bought and confusion abounds.
Leaning towards JGS due to the feedback I have received from others. I know I can send them a dummy round to work from, but just trying to figure out what I would be looking at when they send me back a print that I wouldn't understand.
I haven't done much with the 108. If you plan on the Hybrids with that chamber and FB, the heel of the bullet will be close to being in where the die stops sizing. I like to keep it above that area. Will it function, most likely. How I do it, I like to make the FB fit the bullet where I have it in the case. UNI throater are quite handy. Not sure what I'd do without one...So would those dimensions work with bullets from 105gr - 115gr ? Or would it have to be narrowed down more to something like 108gr only ?
Not offended at all. Lots of good information here, but I also ended up with a lot of questions still unanswered after all my research. After getting a lot of answers to my questions from other shooters, reading all the threads, speaking with a couple of smiths and the reamer manufacturer I plan to use, I have found the best course of action for me is to send some samples to the reamer manufacturer and then discus what I want based on both what I have currently and what I now know that I didn't before.I'm not trying to Hog your post. Just curious as to how also to end up with a final dimensions for the 6 Dasher reamer. Hopefully your not offended by my questions?
Not offended at all. Lots of good information here, but I also ended up with a lot of questions still unanswered after all my research. After getting a lot of answers to my questions from other shooters, reading all the threads, speaking with a couple of smiths and the reamer manufacturer I plan to use, I have found the best course of action for me is to send some samples to the reamer manufacturer and then discus what I want based on both what I have currently and what I now know that I didn't before.
There is no magic reamer. Just like everything else in this game, everyone has an opinion and theirs is always right because it works for them. At some point, just like everything else we do, you just have to make a decision and see if it works out. I am getting closer to that point.
If I make the wrong decision, I will either have it reground, or will have a very slightly used reamer for sale.
here is my 6BRX one i just got made , can compare a few parts to what your looking at getting
View attachment 1181708
Are you saying that the freebore that is good for 105 Hybrid's is or is not good for Bart's Hammer's or Gungnir's? ThanksOn a 1.555 long chamber, the FB you mention is way too short for the Hybrids, like 40 thou short, IMHO. I've been running the same 1.555" chamber for years. My henriksen reamer is a .136" freebore and is too short for the hybrid. I lengthen in a separate operation using a unithroater. If you were to order a reamer with freebore to run hybrids...i will take a guess that .145"-.155" will be good. Other bullets out there, the .105" might be good. Bart Hammers come to mind...
Tip of the day...match your freebore to your intended bullet. This is why many LR shooters have many reamers, lol
Seems to be for sureThe gungirs might be good, but too long for the hammers. I'm sure you can possibly get them to shoot, but best to match freebore to your bullet. And on top of that to add confusion, your overall chamber length needs to be taken into consideration because it will affect where your bullet is seated in relation to touch lands. In simple terms if two reamers has same freebore of .150 and different chamber lenghts, the measured OAL of a seated bullet to just touching the lands will be different. FB is misunderstood by many...