• This Forum is for adults 18 years of age or over. By continuing to use this Forum you are confirming that you are 18 or older. No content shall be viewed by any person under 18 in California.

20 practical reamer

Mark M.

Silver $$ Contributor
I have read the two post on this, But just wanted to make things clear, I know I'm not the sharpest pencil in the drawer,
Looking to put together a 20 practical bolt gun pac-nor 11 twist , My Smith doesn't have a reamer so I'm looking at supplying one, I would like to use lapua brass, so my question is what neck dimension should i be looking at for this reamer? Also, Freebore? Zero or ? shooting 32, 39 Sierra, Would there be a reamer print with the correct dimension I get from someone or copy from a site? Thanks Guys for you Patients
 
Well, this is the one Kevin Weaver developed (the creator) and what I have him use on my rifles. Zero freebore and 0.233" no turn neck, although with Lapua brass it is close. I'm sure others with have some to share.

20P Reamer.jpg
 
I think you need to clarify if your goal is to NOT trim the necks. because brand of brass doesn't matter if you are trimming. the print posted by Jebb is the same as my reamer
 
My Lapua brass (loaded) measures .228 with a skim cut on the necks. as hog says they are very simple. I currently load for five and are my favorite cartridge right now.
 
Lapua brass has a little thicker necks than many other brands of brass and I think that .233 neck is maybe more for using Remington brass. Seems most everyone wants a .235 neck dia. if you are necking down Lapua brass.

My most recent .20 cal is my 20-222 and I'm using necked down Lapua 222 brass and my reamer has a .235 neck. With a fired piece of brass, I have a little less than 1 thou per side. I'm sure there is a certain amount of spring back so I'm sure I have plenty of clearance, but I'm not sure I'd want a neck with anything smaller than .235

I'd have to go look at my reamer print to be 100% sure, but I think the neck diameter on my 20-250 is .236 and I use Lapua brass for that also. Just looked, my 20-250 has a .236 neck per the reamer print.
 
Last edited:
I'm using LC09 223 brass necked down, its .228 loaded and my neck chamber is .232. Use 223 LC brass and save yourself some money it's tough as h$$$.
Lapua is great but I dont think it's necessary for this application.
 
Pac Nor did my 11 twist for my 20 P. I went with their best barrel. It doesn't care which brass I use, it shoots great.
 
With the .20 Practical, I have three of them, thousand of rounds and you will gain ZERO with Lapua brass, neck turned or no neck turn. I have used over twenty different brands of brass, LC, PPU, Remington, Hornady, IMI, Winchester, Top Brass, PMC, Federal, Lapua, ad nauseum. Lapua in the 20P, from my experience, is a waste of money.

My reamer is .233 neck and .000 freebore. Remington loaded round is .228, Lapua .232.
 
Last edited:
You must log in or register to reply here.

Upgrades & Donations

This Forum's expenses are primarily paid by member contributions. You can upgrade your Forum membership in seconds. Gold and Silver members get unlimited FREE classifieds for one year. Gold members can upload custom avatars.


Click Upgrade Membership Button ABOVE to get Gold or Silver Status.

You can also donate any amount, large or small, with the button below. Include your Forum Name in the PayPal Notes field.


To DONATE by CHECK, or make a recurring donation, CLICK HERE to learn how.

Classified Ads

Forum statistics

Threads
165,942
Messages
2,206,462
Members
79,220
Latest member
Sccrcut8

Share This Page

Back
Top