Time to make the donuts....

[geo.ulrich]

Thats what I was trying to see on Jackies jacket but photo is a little dark. You are correct it is a thin section from the drawing process. I would say from to much reduction on the last draw...

 

[Larry Koch]

I lubed up 350 30 caliber cores exactly the same way I did the 6mm and core seated the jackets yesterday evening.
I just pointed them up this afternoon.

Just like the 6mm, they came out .0002 larger on the shank than the squeaky clean cores.
They went in the die find, no different than before. But the extraction stroke was definitely more difficult. Almost aggravatingly difficult. I even stopped after a few and re lubed them, adding about 2 more grains of lube. Nothing changed.View attachment 1658971View attachment 1658972View attachment 1658973View attachment 1658974
You can see from the two sectioned bullets that the core did progress further up in the jacket. The one on the right is the lubed core bullet.
One other thing. The lubed bullets have a faint shadowy ring just above the base. I don’t know what that is all about. The base is about .0002 larger than the shank.

I don’t wish to be pessimistic, but that ring just above the base bothers me. It’s the first time I have seen it on our bullets.

I’ll test them Sunday.

The results look good. But the one the matters is the paper test. I know your going to share.

 

[jackieschmidt]

Just for the record, the lube cored 30’s shot like cr-p this morning. .300 bullets at best.
My regular bullets shot their usual.
I think I simply used too much. I did not have time during the week to do some with less ATF in the Acetone.

I have a 100 yard Club Match this week end, then the Gulf Coast Region in Lake Charles, then the Nationals. I haven’t got any time to mess around with this now. Maybe after the Nationals.

 

[Stumpy1]

This might not be the best place to ask this, but I think there is more bullet making knowledge in this thread than anywhere else I know of, so...

I have attached a couple of pictures of bullets to this post that have some pretty awful looking 'folds' in the jacket. These are from a major manufacturer. I found 5 similar to this in the last 80 or so rounds I have loaded up.

I have a few questions for all the bullet makers here;

1. What causes this?
2. Is it a problem that will show up on target?
3. Should I shoot them?
4. Should I contact the manufacturer?
5. Should I ditch the entire lot of bullets (based on the number found so far)?

Thank you in advance for furthering my education!!!

Frank

 

[AlNyhus]

I got this yesterday. I wonder if Charlie could do anything with this for cores????

 

[ebb]

https://en.wikipedia.org/wiki/Carbonite Did Hans Solo send that to you from the future?

 

[jackieschmidt]

This might not be the best place to ask this, but I think there is more bullet making knowledge in this thread than anywhere else I know of, so...

I have attached a couple of pictures of bullets to this post that have some pretty awful looking 'folds' in the jacket. These are from a major manufacturer. I found 5 similar to this in the last 80 or so rounds I have loaded up.

I have a few questions for all the bullet makers here;

1. What causes this?
2. Is it a problem that will show up on target?
3. Should I shoot them?
4. Should I contact the manufacturer?
5. Should I ditch the entire lot of bullets (based on the number found so far)?

Thank you in advance for furthering my education!!!

Frank

Of course, the first question should be……Who or what company made them?
That can happen during point up. I have had it happen only once.

Use them to clear the barrel after cleaning.

There is no reason to suspect the rest of the bullets.

Look at it this way. That was simply a quality control problem by the manufacturer. But who knows, Those could be coming out of the final operation, cleaned and packaged without a real human ever seeing them.

 

[geo.ulrich]

This might not be the best place to ask this, but I think there is more bullet making knowledge in this thread than anywhere else I know of, so...

I have attached a couple of pictures of bullets to this post that have some pretty awful looking 'folds' in the jacket. These are from a major manufacturer. I found 5 similar to this in the last 80 or so rounds I have loaded up.

I have a few questions for all the bullet makers here;

1. What causes this?
2. Is it a problem that will show up on target?
3. Should I shoot them?
4. Should I contact the manufacturer?
5. Should I ditch the entire lot of bullets (based on the number found so far)?

Thank you in advance for furthering my education!!!

Frank

this usually comes from a crooked pinch trim but a really soft jacket can also be the cause, I would venture to say its probably the first one

 

[Stumpy1]

George, and Jackie, thanks for the comments. I'm not going to out the bullet manufacturer, especially for something that can happen fairly easily, apparently. Mostly, I want to learn about how this happens, and what it means in practical terms.

Having read most if not all of the posts in this thread, I am still amazed that anyone can produce commercial amounts of bullets for anything resembling a reasonable price.

I WILL give the rest of the bullets in this lot a better look-see before I put them in my shooting box though .

Thanks again,

Frank

 

[Larry Koch]

A wise man said to me, it's all about lube control on making great bullets.

 

[AlNyhus]

A wise man said to me, it's all about lube control on making great bullets.

The lube part of bullet making is critical. Quite a few different recipes work but they all share some common traits. As strange as it sounds, jacket lube can be too 'slippery'...it needs a certain amount of drag. Randy Robinett says it best...lube is a necessary evil.

 

[Tricky5225]

I got this yesterday. I wonder if Charlie could do anything with this for cores????

Maybe ask Han Solo

 

[AlNyhus]

Maybe ask Han Solo

Maybe Princess Leia.....

 

[AlNyhus]

It's a cool, windy, rainy day here in The Forbidden Zone....good time to seat cores. They get pushed down using this trick C.S.D.'er (Core Stuff'er Down'er) tool, courtesy of the Hu Hot Mongolian grill.

 

[jackieschmidt]

It's a cool, windy, rainy day here in The Forbidden Zone....good time to seat cores. They get pushed down using this trick C.S.D.'er (Core Stuff'er Down'er) tool, courtesy of the Hu Hot Mongolian grill.

Now that is high teck

 

[Larry Koch]

chop sticks come in handy.

 

[AlNyhus]

Things that make you go "Hmmmmm????"

 

[geo.ulrich]

Al I sent you a pm

 

[AlNyhus]

A real bullet maker would have bullet trays and not be a caveman pushing cores down one at a time with a bamboo chop stick. In an effort to drag my intellect up from somewhere between a single celled amoeba and an early Neanderthal, I decided to improve my core-stuffer-downer tool. Watching an episode of Anthony Bordain's 'No Reservations'...the solution presented itself. There he was...on the street of Hong Kong...eating noodles with fiberglass chopsticks! Quick like a bunny, Jeff Bezos came to my rescue and 24 hours later, a package of 12 pair were at the door of my sod hut on the prairie.

I used one this morning and it worked great. Then, with a flash of new found brain power...I remembered that I also possessed a left hand, complete with opposable thumb. Those stinkin' cores didn't stand a chance now that I could double team 'em. In an instant, I'd gone from the Paleolithic period, blew right past the Mesolithic and landed firmly in the Neolithic period. The CSD tool is also an APO tool. (Core Stuffer Downer/Air Pusher Outer).

Good shootin' -Al

 

[CJ6]

Now that's High Cotton......