What reloading book/manual to get?

[Losthwy]

I have the Lyman 47th. Did some seraching and found some like the ABC's of reloading. Which one? There are two listed by different authors. Some books on Amazon are priced way too much. I not willing to spend a $100 on a book, esp one that isn't very useful. I do not need a book on data. Good illustrations and easy to follow.

 

[TheSnake]

What is your experience level and what are you looking to get out of the book? The reloading manuals have good information in them to get you going. I also like "The complete book of practical handloading" and it's out there used for less than $20 shipped. I am sure there are others that can make suggestions. This site is also a very good resource of information and lots of folks willing to help just by asking.

Welcome to the forum.

 

[Cort]

The Lyman book is an excellent manual with a large section describing the process of reloading. I heartily recommend it. As a beginning reloader, you may want to consider purchasing more than one book in order to get different perspectives on the reloading regimen. One can never be too careful. A "minor" mistake can be costly.

I also use the web sites of the powder manufacturers to confirm load starting points with their powders. And many of the bullet manufacturers have books listing load specifications for their bullets.

Err on the side of too much information and be careful. If you have a friend who reloads, it is a good idea to spend some time with your friend while reloading (if your lucky, maybe you will end up with some reloads for you rather than him ;-) ). That way you can see first hand what the steps are

Cort

 

[Nodak7mm]

I highly suggest you get each and everyone you can get your hands on.. They all offer different info and if there is one thing you can pick up from the book and apply it, then it was worth it...

Bear in mind, Reloading Manuals are "live" manuals, the data contained is constantly revised and always changing.

Rod

 

[Shynloco]

Losthywy,
Are you asking about books more geared to loads with certain bullets (manufacturer driven), books geared to basic reloading methods or books written by and for "precision loading" techniques? I guess it might also be depending on the type of shooting you are doing and the purpose(s) in your reloading. The ABC's of Reloading is a terrific book for learning basic reloading methods. You can get your choice of bullet manufacturer or even powder manufacturer "manuals." And then you can buy books such as those written by Mike Ratigan or Tony Boyer that demonstrate and suggest methods more geared toward "precision reloading" for the "precision and competition shooting" group. Might help us to provide suggestions if you get just a bit more specific on what you are looking for.

 

[jonbearman]

Sinclair used to put out a looseleaf booklet called precision reloading I believe.Maybe someone has a copy they would sell on here.

 

[Losthwy]

I need something for "how to" such as why, how and when to do something such as neck turning. That Sinclair book is favored by a few. Thanks for the suggestions.

 

[treeman]

glen zediker authored a book titled "reloading for competition" it is geared to highpower( across the coarse ), but applies to most shooting intrests. very good book.
regards, Darrrell

 

[necchi]

Go check your local Library, ours has several.
I have heard in some areas theres nothing , but you might as well look.
Free reading is well, free.

 

[K22]

In my opinion, the Lyman Manual is one of the best for the beginning reloader since it covers all the basics and some advanced methods.

If possible, you would be also well served to hook up with an experience reloader, preferably a target shooter or long range varmint hunter, who can also give you some very useful pointers on precision reloading.

 

[bozo699]

glen zediker authored a book titled "reloading for competition" it is geared to highpower( across the coarse ), but applies to most shooting intrests. very good book.
regards, Darrrell

Losthwy,
Darrell has given you the best suggestion for what you have ask for in my opinion, he has a dry sense of humor and sometimes it's a little hard to follow and you may have to read it a gain but not too often, he explains all aspect of reloading and everything else that goes with shooting in great detail and suggestions on equipment needed, a must in my opinion for any shooter to have, I reference my copy quit a lot.
Wayne.

 

[sdeal5]

Totally agree with bozo about zediker. The guy is funny as hell and applies common sense to all aspects of reloading. When he is not sure about something he admits it, and lets you decide for yourself. A very good, informative book.

 

[Joe Maisto]

Losthwy

I have a copy of " HANDLOADERS DIGEST" /94 - 13th edition , edited by Bob Bell I bought new in '94. It has been used but very little by me and I have no more use for it because of my age.
It is complete , for ALL types of handloading, including for hunting AND competition shooting. Furthermore, photgraphs of the available equipment needed for your particular type of shooting.
You can have it for $8.00 plus shipping. Problem is, .......shipping will be as much and probably more. If you wish, PM me.

Joe

 

[Jet]

Read as much as you can on the subject from as many sources as possible. As stated above, the Lyman book is a great manual for you if you are new to reloading. Also, find some folks in your area that reload for the same shooting sports you plan on loading for and start picking their brains and shadow them when possible to watch/learn first hand.

Jet

 

[vtmarmot]

I wish I had read Tony Boyer's book before I ever started handloading. The concept of using a bushing neck die that also sizes the body is the simplest, most accurate way to get accurate handloads and long brass life. This is true whether or not you turn necks, and whether you are loading for competition or hunting. It allows you to size the neck just enough to get good neck tension and bump the body and shoulder just a little. It would have saved me a lot of money, time and aggravation if I'd have known that before I bought my first die.

 

[bozo699]

I wish I had read Tony Boyer's book before I ever started handloading. The concept of using a bushing neck die that also sizes the body is the simplest, most accurate way to get accurate handloads and long brass life. This is true whether or not you turn necks, and whether you are loading for competition or hunting. It allows you to size the neck just enough to get good neck tension and bump the body and shoulder just a little. It would have saved me a lot of money, time and aggravation if I'd have known that before I bought my first die.

I think Tony's book is one of the best I am looking at my copy sitting on my stand by my chair right now, and advise anyone that wants to get into precision shooting to buy a copy, I do think for the beginner that Glens book covers from beginner to expert. I also don't think bushing dies offer much unless you are neck turning, I own a lot of bushing dies and load factory no turn ammo all the time with them but I don't see any better ammo then with a std. die I do agree there are some advantages with them.
Wayne.

 

[MNFinn]

I highly suggest you get each and everyone you can get your hands on.. They all offer different info and if there is one thing you can pick up from the book and apply it, then it was worth it...

Bear in mind, Reloading Manuals are "live" manuals, the data contained is constantly revised and always changing.

Rod

This. I have 4 full manuals, plus the sections I need from another one...looking at getting more

 

[Losthwy]

Thanks for the suggestions.