• This Forum is for adults 18 years of age or over. By continuing to use this Forum you are confirming that you are 18 or older. No content shall be viewed by any person under 18 in California.

Short action 7mm with Mag bolt face using 300 WSM brass.

Definitely going to research the7/300 more and I am running MDT magazine and I can run up to 2.955 OAL. Thanks for your help.
here’s how I run my 7SAUM
Mag length (2.95) 175smk’s for 0-1200 ish yards for fast transitions and follow up shots.
Absolutely wicked on far yonder coyotes!!!! Lol

3.15” oal with 190LRHT or 183smk’s single feed for 1200 and beyond.
The 183 and 190 are actually really impressive past 2k if you have a location with decent spotting.

If I was going to design a cartridge I’d take the 300 WSM, shorten it .1 or so and shorten the body .15 or so to lengthen the neck and run about a .180-.200 freebore

It would look like 300norma improved or 375 enabler.
 
here’s how I run my 7SAUM
Mag length (2.95) 175smk’s for 0-1200 ish yards for fast transitions and follow up shots.
Absolutely wicked on far yonder coyotes!!!! Lol

3.15” oal with 190LRHT or 183smk’s single feed for 1200 and beyond.
The 183 and 190 are actually really impressive past 2k if you have a location with decent spotting.

If I was going to design a cartridge I’d take the 300 WSM, shorten it .1 or so and shorten the body .15 or so to lengthen the neck and run about a .180-.200 freebore

It would look like 300norma improved or 375 enabler.
I don’t know if you’re familiar with what Barnes has done with the .308 212gr Boar Rider bullets, if bullet makers would develop this style bullet, it could be a great option for when you need a better BC without a complete rebuild. What you’re doing with your set up is about exactly what I am looking for. Thanks for your input.
 
You can have your action cut for a Baney box which will give you 3.10 COAL. If that isn't long enough why not just single feed them. If you're planning on shooting a mile, it's not like you won't have time to drop another round in by hand.
 
You can have your action cut for a Baney box which will give you 3.10 COAL. If that isn't long enough why not just single feed them. If you're planning on shooting a mile, it's not like you won't have time to drop another round in by hand.
I think I will go with the 7 SAUM, and run 175s that will run in my $400 dollars worth of mags, single feed longer rounds when I go out farther ranges, like one of the other user mentioned.
 
This is where I am at and where I want to go I had a REM 700 with a 26” Kreiger stainless barrel .308 1-11.25 twist. Had issues with it after I had a local smith work on it, sent to GA Precision, opened the bolt face up, M-16 extractor, trued, Hawkins bottom metal, and they rechambered it to 300 WSM. It’s shooting light out with a 178gr ELDX 3120 with R-17 and descent 190gr Sierra Match.
I want to rebarrel to a 7mm with magnum bolt face, that I can run 175-180gr and use my $400 worth of magazines, and I have over 1000rd of 300 WSM brass. I think I can use my short mag brass to make 7mm SAUM, 7mm SS, but I am very interested in the 7-6.5 PRCW, but not sure if I can use my brass to make them. I know PRC brass is more available, but I don’t want to re invent the wheel, because of the amount of good brass I have.
You can wait like me for the 7 BSM. 7 mm wildcat based on 300WSM with 7SAUM capacity. Supposed to be released some time this year. I don’t do Facebook but you can do a search on Bryan Blake’s paige
 
You can wait like me for the 7 BSM. 7 mm wildcat based on 300WSM with 7SAUM capacity. Supposed to be released some time this year. I don’t do Facebook but you can do a search on Bryan Blake’s paige
Any general specifics of it?
Pushed back shoulder?
 
The Bat Vesper action from Unknown Munitions will get you 3.150 COAL when using their bottom metal and mag. That should let a guy seat the heavy bullets out plenty far and still feed from a mag if needed.

I've actually opened up the load port on Gunwerks short action to accept this setup on a 7 saum and it worked out great.
 
Any general specifics of it?
Pushed back shoulder?
I’ve only seen pictures of the cases at this point and read a little of what FB will allow without an account; but yes, the shoulders are pushed back and flattened to 40. Neck is shortened as well.
 
Its a RSAUM clone using donor Lapua 300 PRC Brass ...I think it was if I remember correctly.
It shoots really well...
 
Sounds like a lot of work. I get wanting to use your pile of brass but you’re gonna spend a lot of time and effort to make this project what you want. I shoot a 7Saum, great cartridge, I’m having three 7Saum improved rifles being built as we speak, one for me and two for friends. I bought plenty of ADG brass first time I could after not being able to get anything but Norma for years. Use your action, use your mags, buy some new brass and go.

It will get you out to a mile but if your really wanting to shoot a mile, if that’s the purpose of this project I’d look at a long action and use one of the big 7s with high BC bullets, I think you’d be happier but that’s just my opinion. I’ve had a few custom rifles over the years that required a lot of work to adapt components I had on hand, I came to the conclusion it’s easier to buy the closest thing to what you need and start there. Time is money too, that being said I understand tinkering in the gun room and playing around is fun too.
 
Last edited:

Upgrades & Donations

This Forum's expenses are primarily paid by member contributions. You can upgrade your Forum membership in seconds. Gold and Silver members get unlimited FREE classifieds for one year. Gold members can upload custom avatars.


Click Upgrade Membership Button ABOVE to get Gold or Silver Status.

You can also donate any amount, large or small, with the button below. Include your Forum Name in the PayPal Notes field.


To DONATE by CHECK, or make a recurring donation, CLICK HERE to learn how.

Forum statistics

Threads
164,955
Messages
2,187,270
Members
78,614
Latest member
dlljr416
Back
Top