Seating depth…what does it do?

[CA_Shooter]

I’m not sure I said seating changes barrel timing rather fine tune. I can tune powder within a tenth gr or kernel and be confident the timing is good yet still influence groups vertical point of impact and irregularities with seating variations.
Added; I don’t pretend to know what’s going on inside a barrel, I’m just trying to describe what I see on paper although I’m but probably not doing a good job of that.
Jim

Didn't mean to specifically point out what you said. Moreso it's been said throughout the thread.

 

[Ccrider]

With Sr Br rifle you can induce vertical and horizontal with seating depth. It can be seen on the target. Probably really shows up at Lr.

Later
Dave

I see this in every ppc load.

 

[Ringostar]

Undoubtedly there's a relationship between seating depth and pressure.

With all of your years as a test shooter for manufacturers, are you willing to share your knowledge and experience? I’m seriously curious to hear your opinions.

 

[Beiruty]

Seating depth would change
1) Effective case capacity
2) Time between initial ignition and time when the bullet engages the rifling
3) Initial bullet speed when said bullet engages the rifling
4) Initial case pressure rise and peak pressure
5) Bullet barrel time +/- time in 2)

 

[Alex Wheeler]

Seating depth does stuff to the tune that that does stuff on target. Thats my technical answer. Most of the time we think in barrel time and exit time. Seating does seem to relate more to touch point than anything. I can cut a barrel to length with a tape measure. They may vary a bit but they will like the same jam or jump to the .001". And in LR we get a very small window, maybe .002 or .003. It just matters. Why exactly, I will leave to smarter people.

 

[David Christian]

I started this thread in the search of knowledge and a way to find an absolute with a specific part of a process. I’ve learned a number of new angles to pursue out of curiosity. Good stuff!

I am a big believer in the frictional process of debate. Everyone gets to postulate and defend their idea as well as hear, interpret and then either accept or debunk others’ ideas. This thread is a good example.

I am still left wondering if anyone on this forum has truly figured out seating depth? Is there a predictive model? Like many of the posts, I am pretty good at trial and error, that is until a variable changes, such as ambient temperature, lands length, rounds down the barrel, dirtiness of the barrel, etc.

Is trial and error periodically throughout the barrel’s life the best route?

DC

 

[BoydAllen]

Seating depth would change
1) Effective case capacity
2) Time between initial ignition and time when the bullet engages the rifling
3) Initial bullet speed when said bullet engages the rifling
4) Initial case pressure rise and peak pressure
5) Bullet barrel time +/- time in 2)

Years ago, I changed my seating depth for a load, seating it deeper into the rifling by .002, but I guessed wrong and it threw my load out of tune. I guess my point is that with such a small move, and the change I observed, I think that the actual mechanism of the change in accuracy will always be no better than a guess. Frankly, I think that our time would be better spent experimenting and taking good notes of what happens when we make a particular change, be it neck tension, charge weight or seating depth, and it would be a lot more honest to simply say that we don't really KNOW what does it but we can know what the effect is. Some of these threads remind me of pre science explanations of the night sky.

 

[Beiruty]

I started this thread in the search of knowledge and a way to find an absolute with a specific part of a process. I’ve learned a number of new angles to pursue out of curiosity. Good stuff!

I am a big believer in the frictional process of debate. Everyone gets to postulate and defend their idea as well as hear, interpret and then either accept or debunk others’ ideas. This thread is a good example.

I am still left wondering if anyone on this forum has truly figured out seating depth? Is there a predictive model? Like many of the posts, I am pretty good at trial and error, that is until a variable changes, such as ambient temperature, lands length, rounds down the barrel, dirtiness of the barrel, etc.

Is trial and error periodically throughout the barrel’s life the best route?

DC

There is no secret about internal ballistic of a bullet.
Whatever variable we consider:

Primers
Powder speed
Powder charge
Case volume
COAL
Bullet profile
Bullet weight
>>> Bullet seating depth
Case neck tension
Bullet caliber
Chamber profile
Barrel rifling
Barrel length
Barrel profile

would change:
Pressure behind the bullet
Bullet acceleration and speed
Bullet barrel time
Muzzle Velocity

As for the implication on accuracy, the major factors that would define the precision of the bullet/rifle are:
Barrel profile, (i.e, heavy 1.2" barrel vs ultralight thin barrel)
Overall weight of the rifle
Rifle build quality

All other factors are minors. When major factors are sub par, the minor factors would play more role in the accuracy of the rifle/bullet. "Tuning" would start getting useful in enhancing the accuracy/precision.

All what you need to know about bullet seating depth

Bullet Jump: Is Less Always Better?

About 2 years ago, Mark Gordon shared some preliminary research he’d conducted with the Applied Bal...

precisionrifleblog.com

More Bullet Jump Research!

This is the 4th article in a series on some new research on bullet jumps. Here is a recap of the pr...

precisionrifleblog.com

 

[Kracken McGraw]

Thanks for this very interesting thread. It sure confirms for me that a test needs to be done at the distance range that I plan on shooting at.

 

[Jager]

Yes it matters. Here's what it looks like in pictures. Two-shot groups.

 

[Bc'z]

Yes it matters. Here's what it looks like in pictures. Two-shot groups.


View attachment 1388449

View attachment 1388450

View attachment 1388451

Excellent example of how seating nodes repeat coming in and out of tune.

 

[Kracken McGraw]

Yes it matters. Here's what it looks like in pictures. Two-shot groups.


View attachment 1388449

View attachment 1388450

View attachment 1388451

I was curious if you go straight to the one hole group, or seat out past it a little for throat erosion.

 

[Liven The Dream]

Neck Tension when my load got close to my target velocity .
Working up a load for my .284 F/Class Rifle with A-4350 !
The different things in play are A-4350 and .284 Lapua Brass ( not 6.5 necked up.
I was doing my standard .015 jump with 180 Berger HB. got up to my target Velocity 277??.
SD was 3.6 5 shots. The grouping was so so ? I get home whats up with this, checking all my steps ?
I come up with same Bushing in Die I used with 6.5X284 necked up Brass ?New .284 Brass thicker necks.
Change Neck Bushing .001 Larger, load test Rounds ( only Change Bushing ).
Five shots at 200 yards covered with 3/8 Target Dot, 2771 AV. SD 4.1 Neck Tension .002.
Now Weather get Better can this get a repeat ? I sure hope so .

Hope This is of some Value

 

[Jager]

I was curious if you go straight to the one hole group, or seat out past it a little for throat erosion.

No, I don't try and second-guess anything else going on with the rifle. The target is the ultimate arbiter of truth for me.

But what is important is that there be a pattern. A single, nice group doesn't cut it. You have to be able to see the tune come in and go out. If you can't see that, then you've still got work to do...

 

[Rtheurer]

Different powders "like" different amounts of neck tension. What powder were you shooting? What caliber?

Mr Boyd.
I was wondering if you have witnessed what i have. Seems like when i run a Faster ( for a givin cartridge) powder vs a Slower burn rate of powder that I end up with better results using MORE neck tension with the faster powder and less neck tension with the slower burn rate of powder. So far that has been my experience when doing a neck tension test.
I was wondering if you have seen that same thing or opposite of what i have witnessed.

 

[BoydAllen]

Mr Boyd.
I was wondering if you have witnessed what i have. Seems like when i run a Faster ( for a givin cartridge) powder vs a Slower burn rate of powder that I end up with better results using MORE neck tension with the faster powder and less neck tension with the slower burn rate of powder. So far that has been my experience when doing a neck tension test.
I was wondering if you have seen that same thing or opposite of what i have witnessed.

When dealing with a new powder, generally I am loading at the range, and I have the means with me (neck bushings) to experiment with neck tension, so I do. It all gets back to testing everything and believing your targets. Getting to the specifics of your question, I have seen it go both ways, so I do not operate on that particular assumption.

 

[GetReal]

My observation / experience is seating depth (1) tightens up groups and (2) helps eliminate that 5th round "flyer" (not caused by shooter error.

Berger told me:

1. Start with a low end powder charge.
2. Do a seating depth test to find what's best. For Hybrid targets, start test at 15 / 30 / 45 / 60 off the lands. And dial it in from there + / - 5 thou.
3. Work up powder charges to get the velocity you want.

 

[JFrank]

I was curious if you go straight to the one hole group, or seat out past it a little for throat erosion.

I wish I had one hole groups like that, I think I know what you’re asking. I see here the tendency to lay down at -.020 so I loaded the next rounds at .017 iirc and let the throat erode into the least vertical, it shot pretty well and after awhile it just wanted the same CBTO for the remainder of the barrel life.

 

[Dusty Stevens]

I was curious if you go straight to the one hole group, or seat out past it a little for throat erosion.

Id rather it shoot now than maybe next match

 

[Kracken McGraw]

Id rather it shoot now than maybe next match

Lol, I bet it might help you win when you find it.