Can some one please tell me in detail what jam means in regaurds to seating depth .... i am a newbe an i thought if your up on the lands there is no more room to lenthen the bullet ?? An woodnt making it longer just push the bullet deeper into the case when u closed the bolt . Making it back to the lands ? I get confussed when people say .015 jam into the lands .... how is that any diffrent then .015 deeper in the case seating depth an to the lands ???? Help
please define
- Thread starter G3automotive
- Start date
Alex Wheeler
Site $$ Sponsor
True jam is the longest you can load a round before the rifling pushes the bullet back in the case. But most people call anything in the rifling "jam", so .010 jam would mean .010 longer than the touch point.
zfastmalibu said:
Now the first part of what ZFast is saying is correct as far as most people are concerned. However, that is a nebulous concept. Every "jam" using that definition would be different based on 1.) neck tension; 2.) type of ogive (secant or tangent) and 3.) the "narrowness" if you will, of the bore diameter. On the other hand, the 2nd portion of his definition is what I believe to be correct. ANY portion of the ogive, past the point of "entrance of the rifling", would be a "jam". Then it is no longer a nebulous term. Whether the projectile has a secant ogive or tangent OR 1K neck tension or 4K, if the bullets' ogive passes INTO the lands, it is considered "jammed" at that point. So a VLD (secant ogive) that is set 12K INTO the lands would be "jammed 12K"... That is the easiest most consistent way to state "jam". At least this is my humble opinion. However, with a light enough neck tension, ALL bullets will "soft-seat" when pressed far enough into the rifling. However, even that would not negate the concept of "anything past the entrance" of the lands would still be a jam..
BoydAllen
Gold $$ Contributor
Back in the day, the term was used, and I believe originated by benchrest competitors and later used and corrupted by those who did not understand the original meaning. For this reason it is best not to assume that a reader knows what you mean whey you use the word, and elaborate in some detail what is meant.
The old school, and to me correct usage is as a noun, not a verb. It is a specific loaded length, that with the neck tension that the load will be shot with, is the longest that a bullet may be seated in that particular barrel, without being pushed into the case as the round is chambered.
This dimension is determined by seating a bullet long enough so that it will be pushed back, chambering a dummy, or if at the range, at the firing line, loaded round. Usually I record the seater setting that I loaded the intentionally loaded the long round, measure the long round, chamber it, remeasure it, subtract that measurement from the original and adjust the seater accordingly. If I want to be say .006 shorter than jam, I add that amount to the setback from chambering the test round, adjust my seater to produce that length, seat the bullet of my test round, verify that is measures what I want it to, and then record the seater setting. With an arbor press seater, with a non-micrometer top, it is the combined length of the seater's stem and cap.
The tricky part of using jam as a starting place is when you want to seat your bullets shorter than it would take to touch the rifling. For this reason its usefulness is greatest when seating some distance into the lands.
The difference in loaded round lenght between just touching the rifling and jam, depends on the shape of the bullet's ogive, the leade angle, and wear. Because of this, it changes over time.
One should also be aware that recent use of the word, has changed it to a verb, as in I jammed my bullets. This use is very imprecise and usually tells the reader little that is useful other than that the bullet was seated to a length longer than it would take to just touch the rifling. Shooters who talk about being "jammed" some large amount may not have even checked to see if their bullets have been set back in their cases as the rounds were chambered. For this and a number of reasons, I stick to the older, and to my view more correct use and definition.
The old school, and to me correct usage is as a noun, not a verb. It is a specific loaded length, that with the neck tension that the load will be shot with, is the longest that a bullet may be seated in that particular barrel, without being pushed into the case as the round is chambered.
This dimension is determined by seating a bullet long enough so that it will be pushed back, chambering a dummy, or if at the range, at the firing line, loaded round. Usually I record the seater setting that I loaded the intentionally loaded the long round, measure the long round, chamber it, remeasure it, subtract that measurement from the original and adjust the seater accordingly. If I want to be say .006 shorter than jam, I add that amount to the setback from chambering the test round, adjust my seater to produce that length, seat the bullet of my test round, verify that is measures what I want it to, and then record the seater setting. With an arbor press seater, with a non-micrometer top, it is the combined length of the seater's stem and cap.
The tricky part of using jam as a starting place is when you want to seat your bullets shorter than it would take to touch the rifling. For this reason its usefulness is greatest when seating some distance into the lands.
The difference in loaded round lenght between just touching the rifling and jam, depends on the shape of the bullet's ogive, the leade angle, and wear. Because of this, it changes over time.
One should also be aware that recent use of the word, has changed it to a verb, as in I jammed my bullets. This use is very imprecise and usually tells the reader little that is useful other than that the bullet was seated to a length longer than it would take to just touch the rifling. Shooters who talk about being "jammed" some large amount may not have even checked to see if their bullets have been set back in their cases as the rounds were chambered. For this and a number of reasons, I stick to the older, and to my view more correct use and definition.
BoydAllen
Gold $$ Contributor
Generally, in the traditional old school use of the word, one does not even refer to where the bullet is touching.There is not an amount of jam, there is how much shorter than jam one is seating, assuming that you are not at jam, which can have the disadvantage of causing bullets to end up stuck in the barrel if a live round is unloaded. Which points to the advisability of using a dummy round, to find jam. (Ask me how I know this.) If for instance, I am seating a bullet .006 shorter than jam, I would say that I am seating six thousandths off jam, or possibly shorter than jam. Jam is a specific measured seating depth for that barrel, bullet, and neck tension. Using the word that way precludes saying that a bullet is jammed by a certain amount. If one were applying that convention, one would either say that one was seating so many thousandths into the rifling, touching , or so many thousandths off the rifling. If you want to make it easier to see rifling marks, which is another way to look at seating depths that are long enough to mark the bullet, pinch a wad of 0000 steel wool around a seated bullet, and apply a good amount of hand pressure while you turn the round in the 0000 a couple of turns. The little marks around the bullet will make rifling contact much easier to see, and won't hurt a thing. Finally, given the way that the use of the word has been corrupted, it is best not to assume what someone means when they use it.
Upgrades & Donations
This Forum's expenses are primarily paid by member contributions. You can upgrade your Forum membership in seconds. Gold and Silver members get unlimited FREE classifieds for one year. Gold members can upload custom avatars.
Click Upgrade Membership Button ABOVE to get Gold or Silver Status.
You can also donate any amount, large or small, with the button below. Include your Forum Name in the PayPal Notes field.
To DONATE by CHECK, or make a recurring donation, CLICK HERE to learn how.
Click Upgrade Membership Button ABOVE to get Gold or Silver Status.
You can also donate any amount, large or small, with the button below. Include your Forum Name in the PayPal Notes field.
To DONATE by CHECK, or make a recurring donation, CLICK HERE to learn how.