Brass or Aluminum reducing inserts for Chargemaster

[Richard Andrews]

I would like to order two of the brass inserts with the added alum. added. please respond email bruce@featherrods.com with total price and address where to remit cost. by the way I ordered a couple of the older model inserts a few years ago and they work fine. hope the new ones are even better.
thanks
Bruce

 

[MDM]

I have more ready to go.

 

[HomeSlice]

I have more ready to go.

I'd like one please

 

[gilmillan1]

I would like a set of the two inserts. How do i pay and whats the total?

 

[MDM]

PM sent. Yes, still making these. Thanks

 

[foxguy]

Chargemaster reducing inserts use and powder clearing question.

Hi, I have ordered and received the 2 piece inserts. They work do work very well.
I load using Varget, H4895, and a few others.

After powder charging the cases I always clear the powder used out of the Chargemaster with the reducing bushing in place it makes impossible to clear all of the powder out of the dispensing tube in the RCBS recommended way. I have resorted to removing the bushing every time and with the tape used to hold the bushing in place the tape gets buggered up after a few times.

Have you found a good way to accomplish the removal of all of the powder from the RCBS 1500 without having to remove the bushing?

 

[ronsroom1]

Would like 1 of each.
Ron

 

[HomeSlice]

Mine arrived a couple of days ago. Previously I has been getting roughly 1/5 overthrows with Varget. Tonight I ran 50 through with the reducer installed and didn't have a single miss. My chargemaster is much more usable now.

Thanks so much for making this thing and sending me one. I couldn't be happier.

 

[ronsroom1]

Mine arrived several days ago.
Should have bought these a long time ago.
Thanks, Ron

 

[riverwolf1]

I would like 1 brass sleeve .308 and the smaller sleeve. Pm me as to where to send the money too.
Thx
Gary Vanlier

 

[Globalstar66]

I just sent you a PM for one of these sets.... Thanks, Robbie.

 

[MDM]

Chargemaster reducing inserts use and powder clearing question.

Hi, I have ordered and received the 2 piece inserts. They work do work very well.
I load using Varget, H4895, and a few others.

After powder charging the cases I always clear the powder used out of the Chargemaster with the reducing bushing in place it makes impossible to clear all of the powder out of the dispensing tube in the RCBS recommended way. I have resorted to removing the bushing every time and with the tape used to hold the bushing in place the tape gets buggered up after a few times.

Have you found a good way to accomplish the removal of all of the powder from the RCBS 1500 without having to remove the bushing?

I leave my inserts in the chargemaster. bump the trickle button until the open slot on the tube inside the hopper is facing down. Pick up the whole unit and tilt it backwards so the powder goes back in the hopper. Rocking it back and forth a little, then empty the hopper back into the powder jug. Then, I tilt the unit clear forward to see if anything comes out of the tube and catch it in the pan.

 

[kerjo]

I leave my inserts in the chargemaster. bump the trickle button until the open slot on the tube inside the hopper is facing down. Pick up the whole unit and tilt it backwards so the powder goes back in the hopper. Rocking it back and forth a little, then empty the hopper back into the powder jug. Then, I tilt the unit clear forward to see if anything comes out of the tube and catch it in the pan.

I put money in your PayPal account using PayPal friends. Did you receive it?
kerjo

 

[MDM]

Yes. Still waiting on your shipping address. This is the 4th time I've asked for it. Don't make me use my google-fu to find you. Lol. Check your messages man.

 

[MDM]

Bump

 

[jp]

let me measure mine and I will order one

 

[jp]

let me measure mine and I will order one

I need one brass .310 with the aluminum insert pm me your payment info thx

 

[Sray53TXTN]

I've had mine for a few weeks and have loaded several rounds of 223, 308, & 6BR with Varget, XBR, and H4895 and what a great addition to my Chargemaster. Speeds things up and consistent accuracy. Great product!

 

[andy 2]

I leave my inserts in the chargemaster. bump the trickle button until the open slot on the tube inside the hopper is facing down. Pick up the whole unit and tilt it backwards so the powder goes back in the hopper. Rocking it back and forth a little, then empty the hopper back into the powder jug. Then, I tilt the unit clear forward to see if anything comes out of the tube and catch it in the pan.

PM sent. Yes, still making these. Thanks

I would like a brass one with small insert. Dia is .310 e-mail atddad@att.net phone 440 478 6973 THANK YOU

 

[MattS]

PM sent