• This Forum is for adults 18 years of age or over. By continuing to use this Forum you are confirming that you are 18 or older. No content shall be viewed by any person under 18 in California.

22 Dasher build maybe ?

Have you considered a 6 Dasher?

Same velocity with 105's with a better BC and barrel life.
 
Now I'm getting that special feeling, you guys know what I mean. That feeling of money leaving your bank account !!!!! Ok, 22 BRA, starting with .100fb, may have to go out further....Do I go with 22 br dies? Or are there specific 22 bra dies? You all have reaffirmed my statements that the people on this forum really are the best, you give your time and expertise and share load info,pictures and specs on bbl's and reamer's. Thank you all, keep the advice, bbl, load info and pics coming....rsbhunter
 
rsbhunter said:
Now I'm getting that special feeling, you guys know what I mean. That feeling of money leaving your bank account !!!!! Ok, 22 BRA, starting with .100fb, may have to go out further....Do I go with 22 br dies? Or are there specific 22 bra dies? You all have reaffirmed my statements that the people on this forum really are the best, you give your time and expertise and share load info,pictures and specs on bbl's and reamer's. Thank you all, keep the advice, bbl, load info and pics coming....rsbhunter
Click to expand...


You'll want more Freebore. 0.100fb had too much bullet in the case eating up capacity
 
Thinking .130 fb? I still don't know what to do for shoulder bump die? Isn't the shoulder angle different on the br Ackley? Looked at dies, but don't see anything specific for bra.? Thanks, rsbhunter
 
rsbhunter said:
Thinking .130 fb? I still don't know what to do for shoulder bump die? Isn't the shoulder angle different on the br Ackley? Looked at dies, but don't see anything specific for bra.? Thanks, rsbhunter
Click to expand...

I run Short Action Customs sizing and seating dies
 
The easy button would be to stick to the 22 Dasher and use your 6 Dasher dies if you are using bushing dies.
 
I know sac makes quality stuff, but at my age , I'm not spending $350 on one die. I'm not shooting championship matches, and prize money isn't more than $10.00 , so it might be advantageous to look into the br or 22 dasher...rsbhunter
 
rsbhunter said:
I know sac makes quality stuff, but at my age , I'm not spending $350 on one die. I'm not shooting championship matches, and prize money isn't more than $10.00 , so it might be advantageous to look into the br or 22 dasher...rsbhunter
Click to expand...

Here a L.E. Wilson 6bra full length bushing sizing die. Just throw in the right 22 bushing and you're ready to roll. I have a few of these dies and they are very nice. They accept Redding bushings as well

1 in stock

WILSON 6MM BR-A FULL LENGTH BUSHING SIZER DIE - Graf & Sons

The NEW Wilson Bushing Type Full Length Sizing Die. This die will allow you to size the case neck to your desired neck tension along with sizing down the rest of the case body at the same time. Die includes an adjustable depth decapping rod. Extra De-Capping Punch included, does not use an...
www.grafs.com www.grafs.com
 
Padom, THANK YOU ! It dawned on me about 30 seconds before I read your post. It had honestly escaped me to look for a 6mm brx bushing die....I am going to order one now, the bushing I'll order after I get a fire formed case and can get neck o.d. #'s..Thank you again for taking the time to re-educate me. rsbhunter
 
My 22BR was able to push the 85.5 to 3200 fps with RL-17. 3050fps is more reasonable with more normal powders. I have had no luck with the 85.5. 80VLD, 90VLD, and the 90 SMK have been fantastic.
 
Evan said:
My 22BR was able to push the 85.5 to 3200 fps with RL-17. 3050fps is more reasonable with more normal powders. I have had no luck with the 85.5. 80VLD, 90VLD, and the 90 SMK have been fantastic.
Click to expand...

What were your seating depth relative to the lands for the 90 vld and 90 SMK?
 
padom, thanks again for the info...I did order the Wilson die from Graf's last night. I will order a Forster 22 micro adjust 22 seating stem to use in my Forster 6mm Dasher seating die and bushing when I get the bbl. Had thought alot going with one of the others (22 br or Dasher) but it seems that the brai will do all I need...I really am indebt to all who responded to all of my questions, and were nice enough to respond...Thank you all.....rsbhunter
 
And we're all D@&$ good at it....I, know at least 5 guy's local that now own Sightron SIII scopes and 6 Dasher or 6 br's because of me !!!! 3 months from now, they will have 22 BRA'S ! Thanks again everyone , it's going to be a fun ride....rsbhunter
 
urbanrifleman said:
What were your seating depth relative to the lands for the 90 vld and 90 SMK?
Click to expand...
I need to go dig up my notes to get you an exact number on the 90VLD because it’s been a while, it was jammed pretty far, perhaps 0.012”?

The 90SMK is my favorite and has been shooting better than anything else and I am jamming those about .007”
 
You must log in or register to reply here.

Upgrades & Donations

This Forum's expenses are primarily paid by member contributions. You can upgrade your Forum membership in seconds. Gold and Silver members get unlimited FREE classifieds for one year. Gold members can upload custom avatars.


Click Upgrade Membership Button ABOVE to get Gold or Silver Status.

You can also donate any amount, large or small, with the button below. Include your Forum Name in the PayPal Notes field.


To DONATE by CHECK, or make a recurring donation, CLICK HERE to learn how.

Classified Ads

Forum statistics

Threads
165,804
Messages
2,203,349
Members
79,110
Latest member
miles813

Share This Page

Back
Top