Search results

  1. need bolt handle welded

    www.accu-tig.com

  2. New twist...separated NECKS!

    This was Norma brass, neck turned, fireformed, and shot a second time. Donuts to dollars it was my fault, turning the neck too low. I have yet to retrieve the neck from the chamber. The load was 31 grains of Varget behind a Sierra 107. The good news is the load hammered at 600 yards. It was...

  3. New twist...separated NECKS!

    Well, I was putting my new 6BRX AR-15 through its paces at 600 yards, when the bolt wouldn't close. Couldn't see any obstructions, but no matter what I tried, the round wouldn't chamber. Finally looked at my brass pile, and found the below pieces of brass...never seen that before!

  4. Where to get military brass processed

    Okay, I'll jump in on this...I don't consider this unsolicited advice, so here goes: I sent River Valley Ordnance (RVO) 17,000 pieces of once-fired match 5.56 brass (a mix of BHA Match, LC XX, and WCC XX), all of which was 77 grain match brass fired in match chambers. This was sent in August...

  5. 6BRX in an AR-15

    Didn't bench them yet...and forgot the chrony. The 30.5 load I shot out of the Punkin' Chunker bolt gun got 2850...and I'm sure I've got losses to the gas system, so I'm going to up it a little bit and see where it's at. The great thing about the AR performance bolt is there's minimal firing...

  6. 6BRX in an AR-15

    To follow up: hand cycled the bolt a thousand times with plenty of grease, and then took it out this morning to shoot it...tried loads of 27, 28, 29, 30 and 31 grains of Varget with magazine length 107's. Function just fine, so it appears the gun just needed to be "shot in". Glad to see the...

  7. 6BRX in an AR-15

    Robert- Sincerely appreciate your interest in my pet project...your advice is well regarded. To answer some questions: the barrel is finished at just over 26", and the gas port is .093 (.125 gas tube). When I have a single round in the C Products magazine, the bolt will not lock back...

  8. 6BRX in an AR-15

    I've built a 6BRX upper for my AR-15, but as expected, I'm having cycling problems...to wit, failure to fully stroke. The rounds feed fine, fire fine, and extract fine, but then the bolt closes on an empty chamber. Best I can tell, the bolt isn't going far enough aft to pick up another round...

  9. 6BRX pressure signs at 30.5 Varget

    Thanks Lynn...anyone out there want to trade some Norma 6BR brass for Lapua?

  10. 6BRX pressure signs at 30.5 Varget

    Thanks for all the input. Forgot to include that yes, it's a Remington 700 (so I guess I'm sending off the bolt to get the firing pin bushed...any suggestions on who to send it to?) and I'm shooting Sierra 107s. I've since tried the CCI BR4's with 30.5 of Varget in fireformed brass, and I get...

  11. 6BRX pressure signs at 30.5 Varget

    Shooters, Need some help here...just built a 6BRX with a 1:8 Kreiger barrel (forgot the land diameter, but it was the tighter of the two offered). I'm using Norma brass and Federal 205M primers. Loaded with 30.5 of Varget for fireforming (with the bullet in the lands), I'm getting...

  12. Spotting Scope

    For a budget, Konus makes a good spotting scope. You'll see a lot of them on the across-the-course highpower competition line. If you have the money, however, the Kowa scopes are crystal clear and reasonably priced for high-quality optics. Barska and Tasco are cheap, but they're also not the...
View older results

Upgrades & Donations

This Forum's expenses are primarily paid by member contributions. You can upgrade your Forum membership in seconds. Gold and Silver members get unlimited FREE classifieds for one year. Gold members can upload custom avatars.


Click Upgrade Membership Button ABOVE to get Gold or Silver Status.

You can also donate any amount, large or small, with the button below. Include your Forum Name in the PayPal Notes field.


To DONATE by CHECK, or make a recurring donation, CLICK HERE to learn how.

Classified Ads

Forum statistics

Threads
165,040
Messages
2,188,890
Members
78,678
Latest member
Janusz

Share This Page

Back
Top