Case trimming carbide cutter
- Thread starter bill2
- Start date
There seems to be plenty around:
Buy Replacement Case Trimmer Cutter and More | RCBS
Shopping for the Replacement Case Trimmer Cutter - Learn more about the latest Case Processing and other hunting or shooting gear at RCBS.
www.rcbs.com
Carbide Cutter Head
Carbide Cutter Head by LYMAN An optional carbide cutter fits all Lyman trimmers. Ideal for volume loader.
www.midsouthshooterssupply.com
3-in-1 Case Mouth Cutters – Forster Products
Select a product according to caliber.
www.forsterproducts.com
Thank You , However not what I'm needing. I need the cutter designed for a drill press. Has to be carbide.There seems to be plenty around:
Buy Replacement Case Trimmer Cutter and More | RCBS
Shopping for the Replacement Case Trimmer Cutter - Learn more about the latest Case Processing and other hunting or shooting gear at RCBS.
Carbide Cutter Head
Carbide Cutter Head by LYMAN An optional carbide cutter fits all Lyman trimmers. Ideal for volume loader.
3-in-1 Case Mouth Cutters – Forster Products
Select a product according to caliber.
Like this?
These are the kind that the WFT uses. I believe somebody here got his off of Amazon.
www.littlecrowgunworks.com
These are the kind that the WFT uses. I believe somebody here got his off of Amazon.
WFT Original Replacement Carbide Cutter | Little Crow Gunworks
Little Crow Gunworks WFT Original Replacement Cutter
I understand the end mill .That is correct. I do need to trim and chamfer inside and outside all at the same time. I see 3ACKLEYS is doing that with Forester product. Is there a one piece end mill cutter made to do all three cuts? Trim and chamfers). I appreciate the help Gents. Buy the way what is WFT?
Worlds Finest Trimmer
Thank You. Bill
Bill Rodolph
Silver $$ Contributor
Forster 3 in1 works great!
Bill - The WFT (Worlds Finest Trimmer) is only going to trim the length. It has been my experience that regardless of the tool design, most multi-purpose tools are either more effective at either trimming case length or chamfer case mouths. You have to decide on what is your primary objective. If you need to remove a lot of material from case length, such as while making 300BO brass, then something like the WFT is more important. My experience is that the "End Mill" cutters are extremely efficient at rapidly removing excess material, but with the potential drawback of it also raising a burr on the inside/outside of the case mouth. You will need to then chamfer case mouths to remove these burrs.
If your cases are finished and only need minor case length adjustment/uniformity and the Chamfer is most important then there are several different tools that will work, both manual as well as powered.
There are a few machines/tools out there that will efficiently/effectively cut both case length and chamfer... the cost climbs quickly. You may find it easier to use two tools to accomplish this task for a fraction of the cost of the high-end tools. Click the link below for a suggestion on a great set-up that is budget friendly.
Click Here is link to cost effective Trimming Solution by F-Class John
If your interested and have no budget constraints then you might be interested in the expensive units .... Giraud, Henderson, 21st Century, IDOD, etc.
Last edited:
Upgrades & Donations
This Forum's expenses are primarily paid by member contributions. You can upgrade your Forum membership in seconds. Gold and Silver members get unlimited FREE classifieds for one year. Gold members can upload custom avatars.
Click Upgrade Membership Button ABOVE to get Gold or Silver Status.
You can also donate any amount, large or small, with the button below. Include your Forum Name in the PayPal Notes field.
To DONATE by CHECK, or make a recurring donation, CLICK HERE to learn how.
Click Upgrade Membership Button ABOVE to get Gold or Silver Status.
You can also donate any amount, large or small, with the button below. Include your Forum Name in the PayPal Notes field.
To DONATE by CHECK, or make a recurring donation, CLICK HERE to learn how.