Labradar Bench Mount

[Pawnee Bill]

Just got my Labradar and tried it out with a tripod, but it wasn't the best fit for my shooting situation. I think a clamp on type mount that I could clamp to the side of my bench may work better.
What kind of similar mounts have you guys found that works?

 

[urbanrifleman]

I have the plate mount from Labradar I can make you a deal on it

 

[shoot4fun]

@arkcomatt makes a really nice bench stand for the Labradar. I have one and recommend it highly.

 

[KenOath]

Just got my Labradar and tried it out with a tripod, but it wasn't the best fit for my shooting situation. I think a clamp on type mount that I could clamp to the side of my bench may work better.
What kind of similar mounts have you guys found that works?

This 3 leg low profile works for me prone or from a bench

 

[WillyTP]

I wish I had saved the picture, but someone on here had theirs mounted in their pelican case that would swivel up and the radar was ready to use. Swivel it down, close the lid and it’s ready for the ride home. Neatest setup I’ve seen yet for one, solves two problems at once.

 

[mjl650]

There are short bench’s at the range I shoot at. I made a mount from a piece of 1 1/4” aluminum tubing and a swivel camera accessory mount. I clamp it to the edge of the bench and can extend it past the edge to where it needs to be located to function properly. I’m traveling today but I can get a picture posted tomorrow.

 

[Pawnee Bill]

There are short bench’s at the range I shoot at. I made a mount from a piece of 1 1/4” aluminum tubing and a swivel camera accessory mount. I clamp it to the edge of the bench and can extend it past the edge to where it needs to be located to function properly. I’m traveling today but I can get a picture posted tomorrow.

Please do. Thanks.

 

[Rope2horns]

@arkcomatt makes a really nice bench stand for the Labradar. I have one and recommend it highly.

This^^^

 

[nmkid]

This^^^

Another vote.

 

[Pawnee Bill]

Another vote.

Does anyone have a picture or link?

 

[Pawnee Bill]

This 3 leg low profile works for me prone or from a bench

Nice set up. My problem is my bench is not wide enough to accomodate the tripod, hence the side clamp idea.

 

[Mulligan]

Does anyone have a picture or link?

https://arkcomachine.com/shop?olsPage=products/quad-base-use-for-lab-radar

CW

 

[mjl650]

Please do. Thanks.

Got home earlier than anticipated and took some pics in my basement. The arm is a 12" long piece of 1 1/4" aluminum square tube left over from another project. The bolt is a grade 8 3/8"x16 and the mini ball head camera mount is a Giottos MH 1004 from Amazon for around $18. The black piece is a sleeve I made to fit over the arm to prevent it from collapsing/bowing when I clamp it down(don't really need it but being anal it gives me peace of mind). Works well, holds the Labradar steady.

 

[Dusty Stevens]

Arkco machine mount is the real deal. And it still fits in the labradar case

 

[Pawnee Bill]

Got home earlier than anticipated and took some pics in my basement. The arm is a 12' long piece of 1 1/4" aluminum square tube left over from another project. The bolt is a grade 8 3/8"x16 and the mini ball head camera mount is a Giottos MH 1004 from Amazon for around $18. The black piece is a sleeve I made to fit over the arm to prevent it from collapsing/bowing when I clamp it down(don't really need it but being anal it gives me peace of mind). Works well, holds the Labradar steady.

Thanks for the pix and info!!