• This Forum is for adults 18 years of age or over. By continuing to use this Forum you are confirming that you are 18 or older. No content shall be viewed by any person under 18 in California.

Putting some shine on old brass

Been cleaning up my 300 brass with walnut and cob media, and all is well. Then I got out my OLD 270 brass and I don't think a week in the walnut would help, and all it is, is tarnish from the air. Is there something I can add to the media that would bring them back to shiny(?) life again?
 
Citric acid chemically removes the oxidation. Put em in a big pyrex bowl with hot water and add some “lemishine” ( a liberal tablespoon not very important to be accurate). Watch the magic happen, and it will seem like magic. Swirl em around a big with fingers, drain and do it one or two more times. rinse twice with fresh so no residual is left in the cases.

Dry with a towel and then dehydrator or oven on cookie sheet.

Won’t hurt the brass at all it’s just surface oxidation.
 
Citric acid chemically removes the oxidation. Put em in a big pyrex bowl with hot water and add some “lemishine” ( a liberal tablespoon not very important to be accurate). Watch the magic happen, and it will seem like magic. Swirl em around a big with fingers, drain and do it one or two more times. rinse twice with fresh so no residual is left in the cases.

Dry with a towel and then dehydrator or oven on cookie sheet.

Won’t hurt the brass at all it’s just surface oxidation.
I see they make 3 different ones, I assume you are using the: Rinse Aid with Citric Acid?
 
https://www.amazon.com/dp/B07CMTVH38/?tag=accuratescom-20

This is what I use, it’s commonly recommended by guys who wet tumble with stainless steel. There are others too, just look on the back to see that it’s citric acid.

I went from wet tumbling, to walnut vibrating with a polish, to just doing a quick rinse with citric acid. I only vibrate now for about 15 minutes to get lube off after sizing.

One bottle has lasted me almost 3 years, so it costs basically nothing. Give it a try and see if it works.
 
Been cleaning up my 300 brass with walnut and cob media, and all is well. Then I got out my OLD 270 brass and I don't think a week in the walnut would help, and all it is, is tarnish from the air. Is there something I can add to the media that would bring them back to shiny(?) life again?
There are many products I personally use an automotive metal polish called white diamond you can get it at any auto parts store
 
If you are willing to clean one at a time, go to an auto parts store. Get some stuff called never dull. Put the brass in a drill and use that stuff. Ive found blackish range brass and it will make it look like new.
 
Been cleaning up my 300 brass with walnut and cob media, and all is well. Then I got out my OLD 270 brass and I don't think a week in the walnut would help, and all it is, is tarnish from the air. Is there something I can add to the media that would bring them back to shiny(?) life again?
Wet tumbling will make them like new inside and out in about 30 minutes.... It's about the only time I wet tumble anymore is to get old nasty brass nice again , then I use the Walnut or Corncob normally...
 
Glad to hear it worked. It really is like magic for those who like shiny brass but still want the inside of the necks to stay carbon coated
 
I use a rotary tumbler . Warm tap water , a short squirt of Palmolive , and Lemmi-shine . About 2 1/2 hours run time , and they look like brand new , out-of-the-box Lapua . If that doesn't give you what you want , then the Never Dull / Drill is your answer . Slow , but amazing results .
 
Big bag of Crushed walnut shells,,, a couple of table spoons of kerosene to the tumbler mix,,, an old army cartridge re-loader fellow shared it with me...

He tumbles two 38 gallon barrels of brass cases every week,,, 1 cup full of kerosene to each barrel that is 2/3's full of walnut shells... 10.000 brass per barrel...

Change out the medium when it starts to get real black,,, I get about Seven to Eight cleans of 200 brass before changing it out...

Just another way to skin the cat... ha

Don
 
Been cleaning up my 300 brass with walnut and cob media, and all is well. Then I got out my OLD 270 brass and I don't think a week in the walnut would help, and all it is, is tarnish from the air. Is there something I can add to the media that would bring them back to shiny(?) life again?
Just a thought, but I have been doing a quick clean with oooo steel wool
 
If you are willing to clean one at a time, go to an auto parts store. Get some stuff called never dull. Put the brass in a drill and use that stuff. Ive found blackish range brass and it will make it look like new.

This is what I do on the rare occasion that I care how shiny my brass is. Never Dull is good stuff.
 

Upgrades & Donations

This Forum's expenses are primarily paid by member contributions. You can upgrade your Forum membership in seconds. Gold and Silver members get unlimited FREE classifieds for one year. Gold members can upload custom avatars.


Click Upgrade Membership Button ABOVE to get Gold or Silver Status.

You can also donate any amount, large or small, with the button below. Include your Forum Name in the PayPal Notes field.


To DONATE by CHECK, or make a recurring donation, CLICK HERE to learn how.

Forum statistics

Threads
165,731
Messages
2,201,381
Members
79,060
Latest member
Trayarcher99
Back
Top