Smith for a Smith...

[Richard Jones]

Can someone recommend a good gunsmith to re-time a S&W 686? I am in Virginia, but can also ship to wherever.

Many thanks.

 

[jackieschmidt]

Is it out of time with too much cylinder rotation or not enough?

And how much are we talking about.?

You should hear the cylinder lock snap in with about 1/16 inch of hammer travel remaining.

 

[DRK]

What is wrong with sending back to S&W?

The S&W DA revolver system is fairly simple to work on by swapping parts without having to hand fit like a Colt. You can likely fix it yourself if you wanted.

Get this book.

Amazon.com

 

[jackieschmidt]

What is wrong with sending back to S&W?

The S&W DA revolver system is fairly simple to work on by swapping parts without having to hand fit like a Colt. You can likely fix it yourself if you wanted.

Get this book.

Amazon.com

If it’s slow on time you can peen the cylinder advance hand and add a few thousandths in length.

Or get one of these. If it is timed slow, this will probably fix it.

Power Custom Oversized S&W N-Frame Revolver Hand | TK Custom Store

Enhance your S&W N-Frame revolver's performance with the Power Custom Oversized hand. Hand-ground from precision tool steel, it ensures perfect timing.

tkcustom.com

 

[Richard Jones]

Not my gun, haven't even seen it. Asking for a bud. I'll see if I can play with it a bit.

So no recommendations for a smith?

 

[Richard Jones]

After talking with my bud, it doesn't sound like a timing issue. DA mode won't rotate cylinder, feels like it's dragging. He's going to drop it by so I can maybe see what's going on......
The book is a good idea, thanks.

 

[jackieschmidt]

What can happen with high recoil revolvers is it develops more forward and aft cylinder play. This can cause the cylinder to actually rub the barrel when subjected to the thrust of the internal hand as it tries to rotate the cylinder.

If this is the case, the cylinder thrust surface on the crane must be addressed.

 

[DRK]

I would measure the barrel cylinder gap moving the cylinder forward and aft. Anything above 6 thou is suspect. You can shim or replace the yoke.

Typically you will see this with K frames shooting loose especially when fed a diet of 110 gr 357 loads screaming.

 

[hpshooter]

David Sams in VA. Goggle search will bring him up.

 

[9146gt]

Center pin loose?
Tom

 

[Richard Jones]

So I finally got the 686 from my bud. Cylinder was very hard to close and found that the cylinder was actually contacting the forcing cone end. Going against my ingrained "I always look for the hard fix", I pushed the ejector rod, brushed under the extractor star, brushed the extractor recess and now it closes perfectly. I didn't see a piece of trash/brass/whatever there, but I apparently displaced something. Couple of days of research, 30 seconds of actual 'fix' and an old toothbrush.

Look for simple first.

Just wanted to update and not leave it hanging. I hate that.

 

[Richard Jones]

And, I forgot to thank all those who suggested fixes.

Thanks to all!

 

[Infrequent Shooter]

Smith for a Colt revolver

Looking for a smith for a 1960s DA Colt revolver. thanks in advance.

 

[Infrequent Shooter]

Frank Glen in Phoenix for Colt revolver work.

 

[Infrequent Shooter]

Frank Glen in Phoenix for Colt revolver work.

Confirming his work. Just received my Colt. Frank put a new/old barrel on my 1960s Colt DA revolver. Excellent job, price is good. If I have any SW work, no doubt he can do. And he is salty. Cheers.

 

[kendog]

Plus 10 for Frank. Now that we are neighbors, spent a few hours looking over his shoulder. He has forgot more than most of us know.

 

[Infrequent Shooter]

Plus 10 for Frank. Now that we are neighbors, spent a few hours looking over his shoulder. He has forgot more than most of us know.

Kendog, I would love to have him for a neighbor. I want to have him in my group when the world goes to shit. He is the most laid back guy I have dealt w in a long time.

 

[kendog]

Kendog, I would love to have him for a neighbor. I want to have him in my group when the world goes to shit. He is the most laid back guy I have dealt w in a long time.

Well... He's a cranky old pr&^k, but aren't we all?? ;-)

 

[Infrequent Shooter]

Well... He's a cranky old pr&^k, but aren't we all?? ;-)

Yep, I get more and more cranky every damn day. I about lost it this evening. My GF and I were eating out, and the waitress wouldn't stop upselling and running her mouth. I about exploded. Gee, how hard is it? And I know they are taught to sell, sell, sell. Yep, cranky old man here!