• This Forum is for adults 18 years of age or over. By continuing to use this Forum you are confirming that you are 18 or older. No content shall be viewed by any person under 18 in California.

Removing Scope Bases

Sly One

Silver $$ Contributor
I recently purchased a very nice, custom, lightweight rifle built on a Remington 700 action in 6mm Remington. It was built in the mid-70’s and has 2-piece Redfield bases. I want to use Talley mounts.

The problem is the Allen screws holding the bases will not budge with moderate force. I think that the builder may have used a Loctite product.

Any suggestions as to how to remove the bases?
 
AND -- don't sabotage your efforts by using poor fitting cheesy, limber allen wrenches that are gonna slip, bend or break. jd

I second this. They make wrenches that are hardened and machined. They are sized right with sharp corners so they will not slip. Way better that the forged or extruded. like most other allen wrenches.
 
I second this. They make wrenches that are hardened and machined. They are sized right with sharp corners so they will not slip. Way better that the forged or extruded. like most other allen wrenches.
Where do you buy Allen wrenches like you've described?
 
I recently purchased a very nice, custom, lightweight rifle built on a Remington 700 action in 6mm Remington. It was built in the mid-70’s and has 2-piece Redfield bases. I want to use Talley mounts.

The problem is the Allen screws holding the bases will not budge with moderate force. I think that the builder may have used a Loctite product.

Any suggestions as to how to remove the bases?
Propane Torch man
It wont hurt the blueing
Drop a little drop of Red ATF on top of the screws first then heat until it bubbles
Put a small amount of force on immediately after heating to see if it budges
(Dont heat your allen wrench!!!)
If no budge...
Remove bolt, and apply ATF from bottom in the thread hole then do the same.
---
In such cases usually the heat expands the bolt screw enough to where it is tight in the threads and may need to cool down first before unscrewing
Which is why I suggest applying a "small" amount of pressure, not full loosening pressure....
..... when still hot just to see if you broke the loctite
I do know many people have used loctite and use the wrong type
There is a small screw Purple Loctite that is specific for this type of stuff, and does not need heat
Use that only for small screws if you like Loctite
------------------------
However, using grease I believe is a better method as the tightness of a fastener is limited to the friction in the threads,
When tightening something that is not lubed or greased - thread friction will give the illusion something is getting tighter when actually the bolt/screw is now only twisting due to the torque applied
When using grease, you can actually get something tighter than if dry and not lubed at all
The bonus of greasing threads is also later being able to remove the screws if need be. since the grease will protect from rusting and ease any friction in the threads when reversing as well.
 
Not to be a negative Nelly, but I’ve unfortunately found that sometimes the screws used are also cheap and just give way when heated because the head softens enough too where the torx in the head strips away with pressure if you try the solder iron method.

If you don’t plan to use the 2 piece base then maybe just drill off the heads and use some vise grips to remove the the rest of the screws
 
One of the best tools for applying heat to small areas is my Blue Point Yak10
butane soldering kit.

While this model is discontinued there are similar products available.
There is a micro torch tip that I have used but the hot air blower is perfect
for applying high temperature heat to a very small area.
 
Where do you buy Allen wrenches like you've described?
I used to fly RC, and it was critical that all the hex head screws in the control system were tightened to a spec that you were confident with. I bought mine at a hobby shop that deals with RC cars and airplanes. I mostly use them now for adjusting triggers.
I think I bought them at Hobbytown.
 
Not to be a negative Nelly, but I’ve unfortunately found that sometimes the screws used are also cheap and just give way when heated because the head softens enough too where the torx in the head strips away with pressure if you try the solder iron method.

If you don’t plan to use the 2 piece base then maybe just drill off the heads and use some vise grips to remove the the rest of the screws
ive had to do this when i broke a torx bit off in a base screw.— i try to replace all size 10 torx screws with 15 torx if i can. the 15s are much stronger and ive never stripped one out or broken a bit off in one like i have 10s
 
Last edited:
Sometime you will find that the screws are in a bind by the torque of the companion screw. Worse comes to worst, you might have to drill off the screw head. This is the reason I never use any product on the threads of these mounting screws.
 
Last edited:
I recently purchased a very nice, custom, lightweight rifle built on a Remington 700 action in 6mm Remington. It was built in the mid-70’s and has 2-piece Redfield bases. I want to use Talley mounts.

The problem is the Allen screws holding the bases will not budge with moderate force. I think that the builder may have used a Loctite product.

Any suggestions as to how to remove the bases?
Have used the torch/screwdriver method and it works well, as does the soldering iron, but I like the heat gun better. Had this same situation just the other day, scope base screw would not budge. Just a few seconds with a heat gun warmed it up enough to release. As stated above, it doesn't take much.
 

Upgrades & Donations

This Forum's expenses are primarily paid by member contributions. You can upgrade your Forum membership in seconds. Gold and Silver members get unlimited FREE classifieds for one year. Gold members can upload custom avatars.


Click Upgrade Membership Button ABOVE to get Gold or Silver Status.

You can also donate any amount, large or small, with the button below. Include your Forum Name in the PayPal Notes field.


To DONATE by CHECK, or make a recurring donation, CLICK HERE to learn how.

Forum statistics

Threads
164,690
Messages
2,182,347
Members
78,464
Latest member
Speedy7722
Back
Top