• This Forum is for adults 18 years of age or over. By continuing to use this Forum you are confirming that you are 18 or older. No content shall be viewed by any person under 18 in California.

Remington 788, in 6mm Remington rebarrel. General questions.

Xerothermic

Silver $$ Contributor
I'm looking to use a PAC-NOR prefit for my new barrel. Urban was gracious enough to answer a lot of my questions and suggested moving to a 6mm cartridge that uses less powder. In this day and age, that makes total sense to me.

I, however, forgot to ask what he would recommend based on 5 shot groups, 24 - 28" medium varmint barrel, 7.5 twist?, 103 to 110 pointy bullets, mostly 600 yd. (on in) informal target shooting and a concern for increased barrel life. I don't mind sizing brass, but really don't want to get into trimming necks or fire forming.

The skinny, sporter barrel just isn't getting it for 3 shot groups let alone 5. So, should I just stay with the 6mm Remington but in a heavier barrel and a faster twist or move on to something more modern based on the above? Any experience, you all can offer up would be appreciated.

Lee in Tucson
 
The 6mm Remington, by some standards, is a barrel burner, especially when compared to the more sedated 6MM BR.

I would simply build a 6BR. Granted, you will not achieve the velocities with 100+ grn bullets as the 6MM Remington, but that 6MM Remington, in general, will not achieve the pure accuracy of the BR.

As for feeding from the magazine, I am sure some length modification would have to be performed to accommodate the much shorter cartridge.
 
jackieschmidt said:
The 6mm Remington, by some standards, is a barrel burner, especially when compared to the more sedated 6MM BR.

I would simply build a 6BR. Granted, you will not achieve the velocities with 100+ grn bullets as the 6MM Remington, but that 6MM Remington, in general, will not achieve the pure accuracy of the BR.

As for feeding from the magazine, I am sure some length modification would have to be performed to accommodate the much shorter cartridge.
Click to expand...
Everything above.
 
jackieschmidt said:
The 6mm Remington, by some standards, is a barrel burner, especially when compared to the more sedated 6MM BR.

I would simply build a 6BR. Granted, you will not achieve the velocities with 100+ grn bullets as the 6MM Remington, but that 6MM Remington, in general, will not achieve the pure accuracy of the BR.

As for feeding from the magazine, I am sure some length modification would have to be performed to accommodate the much shorter cartridge.
Click to expand...
Forgot to mention, that I load 'em one-at-a-time. Thanks, for the reply and suggestion.
 
jsn said:
Who makes a prefit for a Rem 788?
Click to expand...
I doubt anyone. There is nothing complicated about the tenon.
I did one for a friend long ago. The thread is a 1 inch 20tpi, the end of the chamber is flat. The action face has a couple of notches that engage male notches on the recoil lug.

You have to relieve about 3/16 of the barrel end because there is no thread relief in the action. Factory barrels also have about a 1/4 inch wide cut away on the threads so there will be sufficient action screw engagement.
There is no reason why you couldn’t do a barrel nut set up on one. You could use a small shank Savage nut, just place the slightly larger Savage thread on the barrel shank.
 
So. . . for ordering purposes, when we are talking about 6mmBR we are talking about the 6mmNormaBR. Correct? Nobody on this Site's 6mmBR forum refers to it as the Norma but just 6mmBR when offering up load data and such. Just making sure which cartridge we are discussing before ordering.
 
Sorry but, I NEVER liked, the Rear locking Lug's for "Support" NOR, the POOR accuracy from, My 788, in 6 Rem.
Sold it years ago and I Only buy, L-H, Rem 700's or Tikka factory Rifles, Today !
And YES, the 6 XC is the "Easy Button" for, Feeding and, great LR, accuracy with,.. GOOD Barrel Life.
But, I'm opinionated and,.. "Spoiled" !
I'd be, a selling that, 788 in, a New York, Minute to.., a close range, Deer "hunter"
 
Last edited:
Tommie said:
Norma
Click to expand...
I really need to change the way I search for information. I queried the internet and the first, of a list, of posts sent me back to Accurate Shooters. I searched AS with no joy before I even went to the WWW.

Anyways, thank you very much for the quick reply. PAC-NOR had a 6mmbr and a 6mm Norma BR and I wasn't 100% sure what to purchase.

Also, thanks to everyone who commented on this thread. Novice out.
 
Idaho-Lefty said:
Sorry but, I NEVER liked, the Rear locking Lug's for "Support" NOR, the POOR accuracy from, My 788, in 6 Rem.
Sold it years ago and I Only buy, L-H, Rem 700's or Tikka factory Rifles, Today !
And YES, the 6 XC is the "Easy Button" for, Feeding and, great LR, accuracy with,.. GOOD Barrel Life.
But, I'm opinionated and,.. "Spoiled" !
I'd be, a selling that, 788 in, a New York, Minute to.., a close range, Deer "hunter"
Click to expand...
Oh..Oh. The XC rears it's head for the second time in this thread. More research.
 
You must log in or register to reply here.

Upgrades & Donations

This Forum's expenses are primarily paid by member contributions. You can upgrade your Forum membership in seconds. Gold and Silver members get unlimited FREE classifieds for one year. Gold members can upload custom avatars.


Click Upgrade Membership Button ABOVE to get Gold or Silver Status.

You can also donate any amount, large or small, with the button below. Include your Forum Name in the PayPal Notes field.


To DONATE by CHECK, or make a recurring donation, CLICK HERE to learn how.

Classified Ads

Forum statistics

Threads
166,238
Messages
2,214,524
Members
79,485
Latest member
bhcapell

Share This Page

Back
Top