• This Forum is for adults 18 years of age or over. By continuing to use this Forum you are confirming that you are 18 or older. No content shall be viewed by any person under 18 in California.

Questions about FL sizing Die reamer dimensions

I have spec'd out a new chamber reamer, but want to move away from neck sizing and shoulder bumping in separate operations and will have a FL die reamer made too. I have read that when cutting a FL sizing die with a reamer, the reamer should have shoulder and web dims .002 in DIA less than the chamber reamer....IS this enough and what about the neck dia? i will be using a expander to set neck tension. Should i request the die reamer cut the neck out past the lead...or all the way out past the rifling? Will be using a 35 deg shoulder so the brass shouldn't grow more than a few thou after each firing.
thanks in advance!
 
Since you are asking for opinions on this . My opinion is to call Dave Manson Reamers , and talk to the actual "Experts" about this , and discuss what you are trying to accomplish .
Thanks and good idea...was hoping Alex or Dave or other members would chime in since I am pretty sure they have already experimented with making their own dies.
 
Here's the minimums in a perfect world with perfect brass regardless of lot #.
Finish reamer +0.003 over virgin brass
Resize reamer -0.003" under finish reamer

We all know the world is not perfect and brass, any brass is fireformed to fit the chamber.
Real world numbers
Finish reamer +0.006" over virgin brass
Resize reamer -0.0035 under finish reamer

I'd go with a 30 degree shoulder as it facilitates sizing.

Reading your post it seems like you're making the sizing die out of a piece of barrel. If that's the case it won't work. Are you making a bushing FL die?
 
You didn't mention which cartridge, but if it is an big ELR cartridge, that is not in widespread use, plan to make several sizing dies. The big brass is hard to size and you will have some trial and error working out the correct ratio of sizing to avoid extraction issues.

Dave Tooley's advise is exactly correct. Spec the die to the virgin brass dimensions, if possible (and if it is a big ELR cartridge, a 30 degree shoulder is better).
 
Dave, Ray
Thanks, the cartridge is 6x47 for 1000 yard benchrest and I will use die blanks from pt&g or wilson or other since i dont have appropriate bar stock on hand and it will be cheaper since i only need 2 dies, a FL and Seater. Was thinking a 35 deg might increase burn efficiency and maybe give me a little edge over the guys using the standard 30. Plan to shoot this cartridge in light gun as long as i am healthy enough to compete. Been saving a long time and will buy 500 lapua or peterson brass to start. Will take base dims from one of those and your advice. Thanks again!
 
Dave, Ray
Thanks, the cartridge is 6x47 for 1000 yard benchrest and I will use die blanks from pt&g or wilson or other since i dont have appropriate bar stock on hand and it will be cheaper since i only need 2 dies, a FL and Seater. Was thinking a 35 deg might increase burn efficiency and maybe give me a little edge over the guys using the standard 30. Plan to shoot this cartridge in light gun as long as i am healthy enough to compete. Been saving a long time and will buy 500 lapua or peterson brass to start. Will take base dims from one of those and your advice. Thanks again!
I think you're trying reinvent the wheel. And it will cost a lot of money to go around in a circle. But if you just want to experience the challenge and satisfaction of the doing everything from soup to nuts enjoy the trip.
 

Upgrades & Donations

This Forum's expenses are primarily paid by member contributions. You can upgrade your Forum membership in seconds. Gold and Silver members get unlimited FREE classifieds for one year. Gold members can upload custom avatars.


Click Upgrade Membership Button ABOVE to get Gold or Silver Status.

You can also donate any amount, large or small, with the button below. Include your Forum Name in the PayPal Notes field.


To DONATE by CHECK, or make a recurring donation, CLICK HERE to learn how.

Forum statistics

Threads
166,269
Messages
2,215,597
Members
79,518
Latest member
DixieDog
Back
Top