• This Forum is for adults 18 years of age or over. By continuing to use this Forum you are confirming that you are 18 or older. No content shall be viewed by any person under 18 in California.

PLEASE CHECK YOUR POWDER LEVEL BEFORE YOU SEAT THE BULLET!!!

farmerjohn

Gold $$ Contributor
Just getting over surgery and thought I would load up some handgun ammo while I was on "light duty", my old standby load of 8gr of unique and a 260gr WFN cast for my 45 colt is all I ever used in my Colt and Ruger revolvers, plenty stout enough to get the job done and not too much strain on the revolver or me. Just use the trickler on my V3 and loaded up a few, getting the dies set and figured I would check the velocity. I've been doing this for over 50 years, charged 16 cases, phone rings while it's blue toothed to the trickler, I answered it, talked to my son, looked at the charged cases and thought I'll just run these through the chronograph and see what they still do, didn't have my flashlight and almost didn't get up and go get it to check powder levels, see if you can spot it! My Blackhawk might have taken it but I doubt it, that generation II Colt.... I'd probably be getting the pieces of it dug out of me!! Still don't know how I did it, but PLEASE check powder levels... JohnIMG_20220218_141440127.jpgIMG_20220218_141151969_BURST000_COVER_TOP.jpg
 
Glad you did a visual check and great advise. It has always worried me with handgun reloading because unlike rifle it is possible to get a double charge. Even though we would use more powder I have wondered if there is a powder that would fill more than half the case so a double charge would overflow the brass.
 
glad you caught it, I've made 2 boo boo's one was 53 or 55 grs of 4831sc in a 65284 had hard bolt lift couldn't figure it out till I checked my scale, the scale arm was sideways a tad out of the v blocks, I just completely missed it all
 
One of the few mistakes I have made reloading was double charging a .38spl case.... These old black powder cases don't fill with modern powder so half full is double.... I also cought it by checking with my little flashlight.... I don't load any thing now like that and sold the .38 because of it... Even on my Dillon I look into every case before placing a bullet on it , it may not be a fast way but it's a safe way and still a ton faster than my single stage.... The safety rules we use are in place for a reason , they have been around for a long time for a reason also... Glad you checked... Sometimes we all need a little reminder to double check everything....
 
One of the few mistakes I have made reloading was double charging a .38spl case.... These old black powder cases don't fill with modern powder so half full is double.... I also cought it by checking with my little flashlight.... I don't load any thing now like that and sold the .38 because of it... Even on my Dillon I look into every case before placing a bullet on it , it may not be a fast way but it's a safe way and still a ton faster than my single stage.... The safety rules we use are in place for a reason , they have been around for a long time for a reason also... Glad you checked... Sometimes we all need a little reminder to double check everything....
Right. It only takes a few extra seconds to make sure the charges look the same.
 
Glad you caught it!!!! When I load for
My 338 Whisper (10.2 grs) HP38 in a 7 BR case I do visual with flashlight before seating the bullets. Then my OCD takes over and I weight each cartridge after seating the bullet.
 
Just getting over surgery and thought I would load up some handgun ammo while I was on "light duty", my old standby load of 8gr of unique and a 260gr WFN cast for my 45 colt is all I ever used in my Colt and Ruger revolvers, plenty stout enough to get the job done and not too much strain on the revolver or me. Just use the trickler on my V3 and loaded up a few, getting the dies set and figured I would check the velocity. I've been doing this for over 50 years, charged 16 cases, phone rings while it's blue toothed to the trickler, I answered it, talked to my son, looked at the charged cases and thought I'll just run these through the chronograph and see what they still do, didn't have my flashlight and almost didn't get up and go get it to check powder levels, see if you can spot it! My Blackhawk might have taken it but I doubt it, that generation II Colt.... I'd probably be getting the pieces of it dug out of me!! Still don't know how I did it, but PLEASE check powder levels... JohnView attachment 1317904View attachment 1317905
using my dillon 550 for 44 mag. - i use a short piece of wood dowel rod - i stick it in the case after powder charging and mark the dowel at case mouth, then i use it as a powder check gage on every round. Its easy to miss one no matter how you do it. Im stopping using the 550 for handgun loads since it doesnt have room for a powder check die, the way i want to set it up. gonna set it up for 223 and go back to the single stage on handgun loads. i see the one - glad you caught this
 
One practice I have adopted when loading pistol is to place a projectile tip down in the case once it is charged. The next step in my process is seating, so I just flip the bullet over and seat.
If I get distracted or leave the room it is immediately apparent where I left off.
 
on a 50 round loading block with charged pistol cases I run my eyes vertical down the rows then then horizontal across rows TWICE looking for any odd level case, 45yr habit I passed onto my son and grandsons never pull short cuts double check, using powders that doesn't fill 50% of case in my opinion doesn't have to be dangerous.
 
One practice I have adopted when loading pistol is to place a projectile tip down in the case once it is charged. The next step in my process is seating, so I just flip the bullet over and seat.
If I get distracted or leave the room it is immediately apparent where I left off.
Great tip.
Never have I understood why reloaders would charge a bunch of cases before seating.
Charge case, seat !

C'mon guys adopt safer reloading practices !
 
I don’t charge cases in the block. I keep my primed & prepped cases in a Tupperware bin. I grab an empty, charge it and then put it in the block. Yet, I still check them with a light. OCD? Yup! Still have all my fingers? Yup!
 
I leave them upside down until i charge them. That way i can see the primer and know theyre empty
Yes of course, best safe practice. I even flip shot cases in range cases then prep from there and into shallow basins while prepping and finally into the bench block before individually charging and seating and finally into range cases.
Torch on the bench, hell no it's another thing to get in the way of best safe practice.

Never ever is there a case on my bench unless it's upside down.
 

Upgrades & Donations

This Forum's expenses are primarily paid by member contributions. You can upgrade your Forum membership in seconds. Gold and Silver members get unlimited FREE classifieds for one year. Gold members can upload custom avatars.


Click Upgrade Membership Button ABOVE to get Gold or Silver Status.

You can also donate any amount, large or small, with the button below. Include your Forum Name in the PayPal Notes field.


To DONATE by CHECK, or make a recurring donation, CLICK HERE to learn how.

Forum statistics

Threads
166,288
Messages
2,215,933
Members
79,519
Latest member
DW79
Back
Top