• This Forum is for adults 18 years of age or over. By continuing to use this Forum you are confirming that you are 18 or older. No content shall be viewed by any person under 18 in California.

Leopold rings/ nutspliter bad design.

If you have ever seen a nutspliter you know that it pushes a wedge right through a nut thus cutting it in half. Leopold designed these rings the same way as you can see in the picture's. Lucky my expensive scope didn't go by, by. Accuracy did in fact go by, by. Oh, please don't anyone say that i must have over tightened. These are sintered as shown in picture and are easier to break at a weak spot like you see in picture's. Oh, and don't anyone say Leopold usually makes good stuff, that doesn't help.20190618_215043.jpg 20190618_215211.jpg 20190618_215211.jpg
 
Ya i was unimpressed with Leopold rings. Mine did not even fit a PIC rail despite being advertised to fit one.
 
I run those rings on my hunting rifle. They are very sensitive to torque. You must use an accurate inch pounds capable torque driver (i use wheeler engineering brand). The settings are listed in the package documents. Tighten using the x method.
 
I run those rings on my hunting rifle. They are very sensitive to torque. You must use an accurate inch pounds capable torque driver (i use wheeler engineering brand). The settings are listed in the package documents. Tighten using the x method.
I used the why method. I told you not to say that. It would be ok if you were joking but you were not ! It is a bad design and to make excuses is bullshit !
 
I wasn't trying to be rude. Sorry if it came off that way. Those rings takes some finesse to get right. Install the ring cap screws with equal reveal between cap and ring (feeler gauge can be helpful). Then work the x method 1/4 turn at a time till you reach torque specs.
 
I wasn't trying to be rude. Sorry if it came off that way. Those rings takes some finesse to get right. Install the ring cap screws with equal reveal between cap and ring (feeler gauge can be helpful). Then work the x method 1/4 turn at a time till you reach torque specs.
I understand there are many uneducated or inexperienced shooters, but i have been benchrest shooting 30 year's. Mounted about 100 scopes and i am a perfectionist who knows not to over tighten or under tighten . and how to get even ring gap and screw tension. The design is bad , they are sintered so they are more likely to snap at a weak spot. They are made with a weak spot where the metal is only about a sixteenth thick and a wedge is being forced into that weak spot. Doesn't take a rocket dude to see the problem! And just because someone hasn't had a problem has nothing to do with wether it is a bad design, that is just lucky. We should not depend on luck because when we need a rifle for the big buck we don't want failure. I would have not known about this if i had not decided to change scope's. There are probably some out there now broken and the owners don't even know.
 
I've used standard Leupold Rings and bases for years but any future mounts I purchase will be Talley - one piece mounts - which I believe are far superior for a hunter in the field.
 
Update! - i went to bass pro to exchange these rings and saw that this problem is really only on the low rings. The medium and high one's have much more metal in that area so they would not face this issue. I learned something, and now you all too . you can thank me later .!
 
I tried using one set of those. They are awful! Scratched my scope severely and had the hardest time ever getting the reticle to stay level while putting everything together.
Never again!
 
It is not just Leupold , Talley, & Lots of other brands of these high dollar headaches can & do fail. Proper Tempering of screws & nuts is not rocket science. I can't count how many scope screw failures I've seen in the past 40 years. It is just something to plan around . It is aggravating but something you learn to deal with. Mike in ct
 

Upgrades & Donations

This Forum's expenses are primarily paid by member contributions. You can upgrade your Forum membership in seconds. Gold and Silver members get unlimited FREE classifieds for one year. Gold members can upload custom avatars.


Click Upgrade Membership Button ABOVE to get Gold or Silver Status.

You can also donate any amount, large or small, with the button below. Include your Forum Name in the PayPal Notes field.


To DONATE by CHECK, or make a recurring donation, CLICK HERE to learn how.

Forum statistics

Threads
166,809
Messages
2,223,868
Members
79,867
Latest member
Steve1984
Back
Top