• This Forum is for adults 18 years of age or over. By continuing to use this Forum you are confirming that you are 18 or older. No content shall be viewed by any person under 18 in California.

Harbor Freight Sonic cleaners

I still have the one pictured in the article and it is going strong...though I am not sure for how long :)

Doesn't sound real pretty anymore, but still does the job.

http://www.6mmbr.com/ultrasonic.html

Jason
 
I have one, does an ok job, but now that I use the stainless media, I have mothballed it and only use it for non-reloading type cleaning.
 
You get what you pay for with the little "toy" ones, I've used an L&R 3 gallon model for over 20 years, cleans bolts, hand guns and brass. I'll never go back to tumbling for competition brass.

My father-in-law found a good use for it also...small engine carbs!
 
Be careful with the stainless steel tumbling cleaning method, if you have snug chambers. I did about 600 308 cases and shot some of them and they worked fine, then I did some 6 mm BR and could not get them to chamber in my .272 neck gun. I looked at the brass and tumbling in the SS caused the edge of the neck to be slightly peened out, turning 300 pieces of brass I was back to shootable brass. Unfortunately I did the same with my 6.5 x 55 AI brass and had to turn all of that down also.

The cleaning method works great as it removes all of the carbon inside and out and makes the brass look like new. Test some of your brass if you want to try and are using custom chambers, factory chambers seem to work OK as there is more clearance. Me I have mothballed the tumbler that I built for the purpose and will probably unbolt it from its home under my bench and sell it and the SS media, with the above warnings.

wade
 
First, I'm no fan of Harbor Freight. It's made-in-China junk - I've bought heat shrink tubing from there that didn't work. HOWEVER, I did decide to try the Chicago Electric Ultrasonic cleaner for two reasons: 1. I wasn't sure I would like ultrasonic cleaning or if it would be worth the trouble and 2. It was cheap so if it didn't work I wouldn't be too upset.

I read the tech article on here about ultrasonic cleaning, so I bought the 2.5 liter cleaner when it was on sale for $59. I couldn't source any science beakers locally and I didn't want to order them online so I looked around and eventually found some candle holders at a craft store the size of beakers that I figured would work just the same, albeit a little more fragile.

I didn't want to get into the multi-step clean/baking soda/vinegar/whatever so I tried a couple of different cleaners. I found one that works like a champ: Krud Kutter, sold at Lowe's. It's clear, non-toxic, biodegradable, and smells good, so I figured if it didn't work on my brass I could wash the patio furniture with it. ;D

I'm happy to report that I've been using the cleaner, my candle "beakers", Krud Kutter, and I've been tickled pink.

On my very first attempt I played by all the rules in the article: stood the cases up, 15-20 per beaker, 3 480 second cycles, etc. I cleaned some once-fired cases that way and they came out looking brand new so I didn't do anything else. After doing a few batches (roughly 100 cases) that way I found that there was still some crusties in the primer pockets.

The only downside to ultrasonic cleaning that I've found is that the cases take a while to dry. I dried some in the oven on a cookie sheet once but found my wife didn't get all of the grease off of the cookie sheet so I ended up tumbling them afterward. Huge mistake. The tumbler was fine but picking the walnut shells out of the primer pockets reminded me why I came to love ultrasonic cleaning. I bought a brand new cookie sheet, then after a couple of batches I discovered that drying them on 200 degrees causes the brass to tarnish. That's no good either 'cause everyone knows pretty brass shoots better ;D. (I have a modern oven with no pilot light so that's not an option.)

I also discovered that using warm water is better than using the ultrasonic heater. The heater in the cleaner not only heats up the water but gets hot enough to leave stains on the cases. Warm water works just fine.

My current method is to lay them down on their sides, about 15-20 per beaker then fill the water/soap mixture to be level with the water-line in the cleaner; use warm water; run them three 480 second cycles on the cleaner; rinse in cold water; and air dry them for 2-3 days. While drying I stand them up on shop towels. After the first day I pick them up and blow any remaining water out of the primer pockets otherwise they won't completely dry. I found that laying them down ensures the primer pockets get cleaned too. If they're standing up the heads absorb more energy and don't let the crusty stuff come out of the primer pockets as well.

Lastly, the thing makes a really high-pitched whine that irritates my ears so I wear muffs when working around it or leave the room while it's running.

I've done about 1000 rounds this way and they always come out squeaky clean. The cheapo harbor freight cleaner is holding up quite well so far, and I've been very happy with it for $59.

Good luck!
 
wwbrown, did you size after you tumbled in ss media?
How much for your media?

John, what is the life expectancy of the ss media?
Jim
 
Hey dave,
almost the exact same way but if you have central AC,take your cases over to your AC unit and put them up on top of the fan and let the electric bill help you out :O) i dried them pretty quick that way too without the towels and stuff. just a thought.
 
I have had one for a while now, got it on sale for a princely price. I used it to clean EVERYTHING. Used different solutions for whatever I was cleaning at the time. Haven't tried the brass yet, I will have to soon. Cleans up jewelry and fine watches nicely though. For some reason mine crapped out on me. It was going full blast, ended up tripping a circuit in the garage (I was busy that night) and the unit would no longer work- at all. Still had my receipt, explained to them what happened, they didn't really care, and gave me a new one. Haven't even taken that one out of the box yet. Good deal for the money- especially if it's on sale with one of those 20% coupons that you CAN use on sale items.
 
i hate to say it but after using both i am more of the STM guy now. no vinegar, distilled water, and baking soda to deal with. still have both. Thumlers tumbler is expensive but built rather tough!
cheers doc
 

Upgrades & Donations

This Forum's expenses are primarily paid by member contributions. You can upgrade your Forum membership in seconds. Gold and Silver members get unlimited FREE classifieds for one year. Gold members can upload custom avatars.


Click Upgrade Membership Button ABOVE to get Gold or Silver Status.

You can also donate any amount, large or small, with the button below. Include your Forum Name in the PayPal Notes field.


To DONATE by CHECK, or make a recurring donation, CLICK HERE to learn how.

Forum statistics

Threads
165,871
Messages
2,205,022
Members
79,174
Latest member
kit10n
Back
Top