Granite/Quartz scale base question

[bobinpa]

Ok, I hate to sound dumb, but why do you put your scale on a heavy base?

 

[bobinpa]

Ok, but I would think it's only as good as what the base is sitting on. If the bench moves, the granite won't help.... Or am I wrong?

 

[Bojo]

Bobinpa I'm trying to wrap my head around this as well. I know for me air flow in my basement it what I have to watch for. I keep my scale setting on a wooden box I have leveled that sits about 12 "high off of my bench so I do not have to crunch down into bad posture yo read the beam.
I would think that anti vibration would be more important than super heavy base unless said base had plenty of isolation dampness under it.
My last name does end in ski though so I am at a slight disadvantage from the start.

 

[josh shrum]

Both of my granite plates sit on sorbothane pads (feet). Sorbothane is used as a shock/vibration damper in many different industries.

I put 4 under each granite plate.

https://www.amazon.com/s?k=sorbotha...ps,156&ref=nb_sb_ss_i_9_9&tag=accuratescom-20

 

[sdean]

Seems like you could put the pads under the scale. My 120 works just fine sitting on the bench.

 

[Dusty Stevens]

Ferrite rings on the dc side of the power cord. Youre welcome. Put a $10,000 surface plate on a rickety bench and its the same as no plate. Rubber feet under said surface plate is also the same as no plate. Im convinced people read too much. Your scale does need all feet touching the same solid surface, but sitting on formica is the same as putting a 300lb surface plate on top of that formica. Get the ferrite rings, put the cell phone across the room, ditch the old fluorescent lights right above the scale and go get a single marble tile at lowes and youll be set.

 

[oldduc]

I just put my scales on my granite kitchen countertop which are mounted on heavy cabinets screwed to the floor and I don't have to worry about them.

 

[bobinpa]

I agree with Dusty. If you put a piece of granite on a bench that moves, all it does is help hold the bench down. A welded steel frame bench bolted to a concrete floor with a piece of granite for a top would be a different story...

 

[nmkid]

All good ideas but, what do I use to "glue" the tiles together??

 

[STS]

Elmers

 

[Dusty Stevens]

All good ideas but, what do I use to "glue" the tiles together??

Get the right size tile one piece

 

[muleystalker]

All good ideas but, what do I use to "glue" the tiles together??

Return the tiles and buy one piece of granite or quartz tile from the same store and forget gluing.

 

[josh shrum]

I am not sure where the wobbly bench came in.

Prior to putting my scales on granite with sorbothane feet, I could "see" when certain things happened in the house.

For example, I heat by burning wood. Anytime my circulating pump would come on to circulate hot water from the wood boiler, I could "see" those vibrations on my FX120i. Same with someone walking around on a different floor of the house. Hell, even our cat could make that scale move when he is into the catnip.

These are scales that are already on a line conditioner, on a solid bench, no where near aircon or florescents.

Did the granite with sorbothane feet make the scales more accurate? No, it made them easier for me to use. My reasoning was that any vibrations would have to travel through my bench, then through the vibration dampening sorbothane, finally transferring any remaining energy to some very heavy granite blocks. So far that seems to be the case.

Will they fix an already mediocre setup? Unlikely, and I doubt that many of the folk going to this level are working from a mediocre setup.

nmkid, I would suggest pure silicon caulk that you can get at you local hardware store. It should offer some vibration damping of its own, which is what we are after here.

 

[Jimmy James]

I have a dedicated little side table I got off amazon for my scale. 50# of lead shot in the base of the table and it sits on a concrete floor. My Newton 123 will not level at least according to it's built in bubble level (that sits at a 45 degree angle ???). It has the ferrite choke built into the line. Temperature fluctuations and draft/air movement affects it more than anything else.