• This Forum is for adults 18 years of age or over. By continuing to use this Forum you are confirming that you are 18 or older. No content shall be viewed by any person under 18 in California.

Grains for 45acp hollow point

9mmAnimal

Silver $$ Contributor
Bought some 45acp 230 grain hollow point bullets from midway,can't seen to find load data using titegroup, accurate #5 and alliant
 
Last edited:
I think you're looking for load data.
The title of your thread should probably reflect that instead of using a measurement of weight as a question.

For people to answer your question, they will also need to know what powder you have on hand that is suitable for the 45 ACP.
 
I think you're looking for load data.
The title of your thread should probably reflect that instead of using a measurement of weight as a question.

For people to answer your question, they will also need to know what powder you have on hand that is suitable for the 45 ACP.
Thanks, I have a few powders titegroup, accurate #5 and alliant
 
Did you weigh one of the bullets? very unusual 230 grn HP in 45 ACP. you can use round nose data, check the OAL of a round nose, if the HP is 230 grn. and adjust OAL. make 1-2 and see how they feed in your gun. Bulls eye shooters love the HP in 185-200 grn.
 
You’ll find allot of handgun load information on the site below. The link is for the 45 cal section so just do a search on one of your powders for the Grain bullet you have. Competition related so they have to make a power factor so you can just cut back a bit on load.

Example:
Bullet: Speer 230 gr. Gold Dot HP
Powder: Accurate #5 7.8
Primer: Federal 150
Case: Winchester
OAL: 1.200
Avg. Vel.: 839 fps
ES: 34
SD: 13
Recoil Spring: Wilson 15 lb. with Wilson Buffer Pad
 
Last edited:
Did you weigh one of the bullets? very unusual 230 grn HP in 45 ACP. you can use round nose data, check the OAL of a round nose, if the HP is 230 grn. and adjust OAL. make 1-2 and see how they feed in your gun. Bulls eye shooters love the HP in 185-200 grn.
Thanks bullet weight 229.3 gr hodgdon titegroup says 4.8 grains of titegroup
 
You’ll find allot of handgun load information on the site below. The link is for the 45 cal section so just do a search on one of your powders for the Grain bullet you have. Competition related so they have to make a power factor so you can just cut back a bit on load.

Example:
Bullet: Speer 230 gr. Gold Dot HP
Powder: Accurate #5 7.8
Primer: Federal 150
Case: Winchester
OAL: 1.200
Avg. Vel.: 839 fps
ES: 34
SD: 13
Recoil Spring: Wilson 15 lb. with Wilson Buffer Pad
Thanks makes it subsonic
 
Presume you know what you’re doing, so forgive this precautionary post. 4.8gr is listed as maximum load for 230 gr FMJ. May be fine, but best practice might be to load a bit under that (10%?) and work up to ensure safety in your pistol. No offense intended. Be safe and have fun.
 
Presume you know what you’re doing, so forgive this precautionary post. 4.8gr is listed as maximum load for 230 gr FMJ. May be fine, but best practice might be to load a bit under that (10%?) and work up to ensure safety in your pistol. No offense intended. Be safe and have fun.
Thanks I always err on the side of caution, always check my weapon, make sure everything is cleared if not I do it myself, had a buddy use one of my ARs long time ago he was trying subsonics, I guess he wanted 2 quick shots,I was stupid to let him use my gun never again he destroyed my upper,round didn't exit the barrel second one destroyed the upper.
 
I used to use AA#5 powder for 230 gr. HP carry loads. 8.5 is about max and 8grs is a good target load. But the residue from the powder contains little tiny balls in it. It accurate powder but those little balls did not sit right with me in a 1911 pistol, so I stopped using it years ago.
 
I used to use AA#5 powder for 230 gr. HP carry loads. 8.5 is about max and 8grs is a good target load. But the residue from the powder contains little tiny balls in it. It accurate powder but those little balls did not sit right with me in a 1911 pistol, so I stopped using it years ago.
Thanks I'll use my accurate #5 8grains do a couple of tests then load up a few mags for my XD I'll feel safe
 
Thanks I'll use my accurate #5 8grains do a couple of tests then load up a few mags for my XD I'll feel safe
That's good. That's what I used. It's just around 800 fps or a little more or less, depends on your pistol. Above that at 8.5 is +P. AA#5 is not a soft ball powder with not a lot of wiggle room but is accurate. If you try to down load the powder it burns dirty and is not very accurate. That's what I mean by wiggle room. Just for you to know Hornady lists for AA 5 powder and the 230 HP bullet; 700fps is 7.1grs. and 8.3grs is 850 fps. Nosler is 7.5grs. at 740fps and 8.5grs. for 840 fps. I get over 900 fps in a 1911. and Sierra says; 7.6 is 700 fps and 9 grs. is 850 fps. I would never try that much AA #5 powder with 230 gr bullet. Stay with 8 grs. to 8.3 grs. and you will be okay. As you can see, the information is all over the place with this powder for a 230gr. bullet.
 
Last edited:

Upgrades & Donations

This Forum's expenses are primarily paid by member contributions. You can upgrade your Forum membership in seconds. Gold and Silver members get unlimited FREE classifieds for one year. Gold members can upload custom avatars.


Click Upgrade Membership Button ABOVE to get Gold or Silver Status.

You can also donate any amount, large or small, with the button below. Include your Forum Name in the PayPal Notes field.


To DONATE by CHECK, or make a recurring donation, CLICK HERE to learn how.

Forum statistics

Threads
165,582
Messages
2,198,720
Members
78,989
Latest member
Yellowhammer
Back
Top