CIP Reamer spec needed, 284 Winchester

[AckleymanII]

Does anyone have a print of a CIP reamer drawing in 284 Winchester?

Thanks in advance

Keith

 

[LC Tikka]

Does anyone have a print of a CIP reamer drawing in 284 Winchester?

Thanks in advance

Keith

Results of a quick search.
LC

https://www.google.com.au/url?sa=t&...FjACegQIAxAB&usg=AOvVaw31pPAuKN2yhYLes80EwNKp

 

[AckleymanII]

Results in MM?

 

[Robert]

Does anyone have a print of a CIP reamer drawing in 284 Winchester?

Thanks in advance

Keith

Thanks in advance

Keith
PM sent
R.G.C
https://c-g-designs.blog4ever.com/

 

[DaveTooley]

Go to the source. SAAMI has both Imperial and metric on everything I ever looked at.

https://saami.org/wp-content/upload...99.4-CFR-Approved-2015-12-14-Posting-Copy.pdf

 

[DaveTooley]

Go straight to the source. It only took two minutes to find all this.

 

[AckleymanII]

Not what I am looking for

 

[284winner]

Keith,
What exactly is the difference between the European reamer (CIP)spec and the US(Saami) spec ?

 

[DaveTooley]

What are you looking for?
My last post was the CIP print you wanted.

 

[shortgrass]

A C.I.P. print will always be in millimeters, and that is what you asked for, a CIP drawing. Europe doesn't use English units of measurement. To convert, multiply millimeters by .03937, and that'll give you the measurement in inches. The result will give a measurement in inches that'll go to five places to the right of the decimal point. Or, there are numerous mm to inch conversion calculators available on-line. Chances are, CIP specs mirror SAAMI specs as the .284 Win was an American development.

 

[std7mag]

Call PT&G or Manson reamers.
They already have the drawing on file.

 

[AckleymanII]

https://www.bing.com/images/search?view=detailV2&ccid=NY3eBaC/&id=D58CEA9E64D5CFA045FB45092068CEFF17C2C08F&thid=OIP.NY3eBaC_ZMf6n9CM79d4kQHaE6&mediaurl=https://www.kelbly.com/wp-content/uploads/2019/09/284-Win.-CIP-Carbide-Reamer-001.jpg&exph=597&expw=900&q=284+winchester+cip+reamer+print&simid=608040181856472781&selectedIndex=0&ajaxhist=0

https://www.bing.com/images/search?view=detailV2&ccid=Upguy2vw&id=033C37B9EC71D9D8C1D21D066DB6C7244C8F540E&thid=OIP.Upguy2vw6SWBmx2W8ZOJagHaB4&mediaurl=http://www.tmtpages.com/LinkSkyImages/forum_images/7mm-08-rem/284_Winchester_C.I.P._Standard~Barrel_284_Winchester_C.I.P._Standard_Rot_Cutaway_A_TMT_Design_Revised_287-277-155_Rot.Jpg&exph=742&expw=2920&q=284+winchester+cip+reamer+print&simid=608008149987165534&selectedindex=21&ajaxhist=0&vt=0&sim=11


friends custom Rifle on fired Lapua is .5035 in the web

 

[tobnpr]

Don't know why the OP is looking for CIP dimensions, no practical difference between CIP and SAAMI specs...
Went through this exercise for a .284 Win Match reamer a year ago.
Had an opportunity to pick one up for a build, brand new (no wait...)- but was ground to CIP specs (with a tighter neck).

Checked all dimensions on print (and discussed on the 'Hide as well)- any differences noted between the prints were well within the dimensional tolerances anyway. Exactly the same animal.

 

[AckleymanII]

In the case of the 284 after research, I found the same thing as you tobnpr.

Since Lapua, Norma, and other European brass runs larger in the web and neck than American brass, some of the reamer prints that I have for this brass designate CIP on it from the reamer maker, which is what caused my confusion. I assumed that they had converted mm to inches, indicating larger dimensions than SAAMI dimensions. This was an incorrect assumption, it was just a custom reamer designed for European brass.