Brux customer service
- Thread starter davidpatton
- Start date
hogpatrol
Gold $$ Contributor
The only way two people can keep a secret is when one of them is dead.Well there goes the cost and available Brux barrels
Glad I squirreld up on a few!!
Jim
Brux is and has been the maker of premium barrels. Their attention to detail is part of the reason. The following excerpt shows some of their exceptional efforts to insure a quality product. James
After cutting to length, the blank is rough turned in a lathe. Next, it is drilled with a Barnes gun drill by an “oil-through” process. The barrel is drilled at 3600 RPM’s while being flushed with the oil. This drills the barrel to 0.005 inch under “land” diameter at a rate of 1 inch per minute.
The barrel is then thoroughly cleaned and sent back to the lathe to finish the contour of the outside.
After another cleaning, the blank is reamed on a Pratt and Whitney reamer in another “oil-through” process. The 0.005 inch left in the drilling process is reamed away in order to give the proper “land” diameter.
After yet another cleaning, the barrel is lapped to remove any slight tool marks left by the reamer. The barrel is inspected with a borescope and goes no further if it does not meet the strict Brux standards.
After another cleaning, the barrel goes to the rifling machine. In a 4-groove barrel like the one I have, each groove is cut separately. (i.e. Single point rifling) After a small amount is scraped from the first groove, the blank is rotated 90 degrees. After four of these rotations (360 degrees), the rifling cutter head is raised to shave off the next bit of material. This process is repeated over and over until the proper groove diameter is reached.
Once again the barrel is cleaned. After the cleaning, it is given a final lapping. This is to ensure an ultra-smooth bore. The barrel receives another inspection with the borescope before being cleaned and packaged for shipment.
Although many think that premium barrels are overpriced, all one has to do is read the above to dispel that notion.
After cutting to length, the blank is rough turned in a lathe. Next, it is drilled with a Barnes gun drill by an “oil-through” process. The barrel is drilled at 3600 RPM’s while being flushed with the oil. This drills the barrel to 0.005 inch under “land” diameter at a rate of 1 inch per minute.
The barrel is then thoroughly cleaned and sent back to the lathe to finish the contour of the outside.
After another cleaning, the blank is reamed on a Pratt and Whitney reamer in another “oil-through” process. The 0.005 inch left in the drilling process is reamed away in order to give the proper “land” diameter.
After yet another cleaning, the barrel is lapped to remove any slight tool marks left by the reamer. The barrel is inspected with a borescope and goes no further if it does not meet the strict Brux standards.
After another cleaning, the barrel goes to the rifling machine. In a 4-groove barrel like the one I have, each groove is cut separately. (i.e. Single point rifling) After a small amount is scraped from the first groove, the blank is rotated 90 degrees. After four of these rotations (360 degrees), the rifling cutter head is raised to shave off the next bit of material. This process is repeated over and over until the proper groove diameter is reached.
Once again the barrel is cleaned. After the cleaning, it is given a final lapping. This is to ensure an ultra-smooth bore. The barrel receives another inspection with the borescope before being cleaned and packaged for shipment.
Although many think that premium barrels are overpriced, all one has to do is read the above to dispel that notion.
Upgrades & Donations
This Forum's expenses are primarily paid by member contributions. You can upgrade your Forum membership in seconds. Gold and Silver members get unlimited FREE classifieds for one year. Gold members can upload custom avatars.
Click Upgrade Membership Button ABOVE to get Gold or Silver Status.
You can also donate any amount, large or small, with the button below. Include your Forum Name in the PayPal Notes field.
To DONATE by CHECK, or make a recurring donation, CLICK HERE to learn how.
Click Upgrade Membership Button ABOVE to get Gold or Silver Status.
You can also donate any amount, large or small, with the button below. Include your Forum Name in the PayPal Notes field.
To DONATE by CHECK, or make a recurring donation, CLICK HERE to learn how.