Anyone have any experience with Longevity Welders

[Rustystud]

I am looking at the Longevity 200PI (three in one machine) anyone have any experience with them?

Nat Lambeth

 

[lelongcarabine]

Do you have one or are you considering?

 

[lelongcarabine]

Bump! Nat! I have not personally used that machine. However, I worked in the welding trade for more than 30 years, with certifications. While I do not know everything and the new equipment available is pretty good stuff. Just be aware that electronics need maintainence and protection from power surges. If you buy from someone who can service your equipment (unless you do that yourself. Dust accumulation removal is a biggie) you may save youself alot of headache and down time, especially for business related usage. Respectfully, Greg(lelongcarabine)

 

[Dans40X]

Nat,
Purchase equipment that has blue cabinetry-Miller Electrics.

Saves alot of BS in the long run!!!!!!

 

[AusFclass]

plus 1 on the millar gear!

im a accredited pressure vessle welder in australia and have used and destroyed plenty of welding equipment while at work.

i purchaced a millar dynasty 200 ac/dc pulse for myself at home and have to say its probably the smoothest welder with the most stable arc at low amps i have used.

because most of the new welders use inverter technology they have plenty of circut boards and gizmos inside. what usually happens is metal grinding sparks and dust get drawn into unit and short out the boards. keep the welder covered when not in use and every 3-6 months take the outer caseing off and give it a good blow out with the compressor.

also check that the plugs on the welding cables ( that twist into the welder) and earth clamp are in good condition. poor connections create heat and earthing problems all are not good for modern inverters.

by buying a well known brand you will be able to purchase replacement parts and be able to have the welder repaired locally if required.

good luck!

 

[blawton]

Another big +1 on the miller. Its what we settled on and wont be buying anything else until they can prove there stuff works better.

 

[Dans40X]

Nat,
Don't blame me!!!!!

Now,put the "Big Blue" inverter machine to work!!!

 

[lelongcarabine]

plus 1 on the millar gear!

im a accredited pressure vessle welder in australia and have used and destroyed plenty of welding equipment while at work.

i purchaced a millar dynasty 200 ac/dc pulse for myself at home and have to say its probably the smoothest welder with the most stable arc at low amps i have used.

because most of the new welders use inverter technology they have plenty of circut boards and gizmos inside. what usually happens is metal grinding sparks and dust get drawn into unit and short out the boards. keep the welder covered when not in use and every 3-6 months take the outer caseing off and give it a good blow out with the compressor.

also check that the plugs on the welding cables ( that twist into the welder) and earth clamp are in good condition. poor connections create heat and earthing problems all are not good for modern inverters.

by buying a well known brand you will be able to purchase replacement parts and be able to have the welder repaired locally if required.

good luck!

I am a MILLER FAN, myself! I have also used Lincoln, Hobart and a whole list of other brands. Miller equipment is in my shop!It has served me well for many years.
I would like to add an additional point to this list. Make sure you use surge protection equipment on welding power supplys that rely on computer technology. Here is an internet source of equipment that has some of the best prices I have seen. I am not affiliated nor do I get a commission if you make a purchase. You may also be better off to work with a local dealer so you have service and parts available, locally. Greg
Used equipment; http://business.shop.ebay.com/Welders-/113743/i.html?Processes=TIG&_trkparms=65%253A12%257C66%253A2%257C39%253A1%257C72%253A2608&_catref=1&_dmpt=BI_Welders&_npmv=3&_trksid=p3286.c0.m14&_pgn=2

Newequipment; http://www.weldingsuppliesfromioc.com/servlet/the-TIG-WELDERS-cln-Miller/Categories

 

[Kenny474]

Miller or Hobart. While I would take a Miller over a Hobart any day, I have used both extensively and they are both nice machines.
I used to build short track cars with a friend and we used both.
Also used Miller TIG's at another place I worked. Big liquid cooled monsters, some of the nicest stuff I have even struck an arc with.

I can't see going wrong with a Miller, unless you buy an underpowered machine, in which case that would be your fault and not the machine's.

I learned to weld on a Miller in school and not much else has ever been as nice to use.

Though if you are going to go with the Longevity I would consider the 250pi, as it is better to have power and not need it, than need it and not have it.

 

[Rustystud]

Followed Dan's Advice

I bought a Miller Dynasty 200DX machine.

Cost more but I beleive it will be well worth it in the long run.

Nat Lambeth

 

[lelongcarabine]

Rustystud, You have a fine machine! Dont forget surge protection! Greg