Action/barrel threads

[ellisprelli]

Hello, can some one show me or inform me about common barrel/action thread sizes.
Is somewhere a list over thease dimensions, or you can paste it in here.

Sako 75/85
REM
Win
Howa... and etc.

if some one has it in a spread sheet or a .doc file pls. send it to erlingur@centrum.is

 

[jonbearman]

I would think a call to shilen would get you the answer you seek.

 

[Jdaniel343]

Here area few:

Action threads length Reciver OD? other
Mauser lrg. Ring 1.1x12 1.41”

Mauser sm. Ring .98x12

CZ 550 1.1x12.7

BBK-02 1.1x12

Rem 700 1 1/16”x16 .885
1.0625x16
Win 70 1x16

Ruger 77 1x16 1.41”

Sako

Weatherby mk V 1.06x16 .7
1 1/16x16
Browning A-bolt

Ruger no. 1 1x16”

Rem Rolling block
No. 1 smokeless 1.055x12 square 1.43”

Win 1885 High wall

Sharps 1874

Savage 110 < 2001 1.05x20
Short magnum>2001 1.125x20 G series, noticeable step after threads
CRF 1 1/16x20
1.0625x20
Bolt Shotgun 1.1x20?

MRC 1999 1x16 UNF 2B .75

Enfield M-17 x10 square

Enfield SMLE

Mosin Nagant .97”x16 or 1x16”

Steyr M-95 1.020x14 tpi V .693” shank

Win 94 .809x20
Win 94 BB .875x28?

Rossi 92

Marlin 336 .775x12 square .85”

Marlin 1895 45-70 same as 336, 450 may have been changed to a v thread.

Savage 99

Norinco Win 1887 lever shotgun 12 ga. 1.1x26 proofed to 43ksi!

Norinco Win 1897 pump shotgun 12 ga. Proofed to 43ksi

lar45; Large Martini action, 1X14, aprox .750 shank.

Browning BPCR and maybe all the Browning 1885's, as quoted to me on the BPCR Board, are .935" outside diameter, shank length is .920" and the threads are 20 per inch with a standard 60 degree form.

Very similar to the Winchester 1885 but for the 20 threads per inch instead of 16 per inch in the Winchester.

Enfield Eddystone Model of 1917 barrel threads are 1.125 with 10 SQ T.R.I., length of barrel threads is .800 inch also stated as 1.125"x10, square threads

Enfield SMLE -
.687" Dia +.100 lip x .900" Root Dia x .997" Dia x 14 V-TPI.

Enfield P-14 -
.720"L +.045"Lip x 1.085" Root Dia X 1.125" Dia X 10 SQ-TPI.

Enfield 1917 -
.800" Dia x 1.085" Root Dia x 1.125" Dia x 1o SQ-TPI w/45-degree chamber cone.

Sako -
L46 = .845"L x .855"Dia x 16 V-TPI,
L57 = .984" Dia x 17 V-TPI,
L579 & early L61 = .870" L x 1.0" Dia x 16 V-TPI,
Late L61 = Same as L579, but 1.046" Dia.

Browning A-bolt
Old: 15/16 x 20
New: 1' x 32

Here's a list of dimensional action threads from Cast Boolits site. I cannot guarantee just how accurate it is. I do know that Remington's 1.060 is correct and have used them to rebarrel Turk Mausers.

Action threads length Receiver OD? other

Mauser lrg. Ring 1.1x12 1.41”

Mauser sm. Ring .98x12

CZ 550 1.1x12.7

BBK-02 1.1x12

Rem 700 1 1/16”x16 .885
1.0625x16
Win 70 1x16

Ruger 77 1x16 1.41”

Sako

Weatherby mk V 1.06x16 .7
1 1/16x16
Browning A-bolt

Ruger no. 1 1x16”

Rem Rolling block
No. 1 smokeless 1.055x12 square 1.43”

Win 1885 High wall

Sharps 1874

Savage 110 < 2001 1.05x20
Short magnum>2001 1.125x20 G series, noticeable step after threads
CRF 1 1/16x20
1.0625x20
Bolt Shotgun 1.1x20?

MRC 1999 1x16 UNF 2B .75

Enfield M-17 x10 square

Enfield SMLE

Mosin Nagant .97”x16 or 1x16”

Steyr M-95 1.020x14 tpi V .693” shank

Win 94 .809x20
Win 94 BB .875x28?

Rossi 92

Marlin 336 .775x12 square .85”

Marlin 1895 45-70 same as 336, 450 may have been changed to a v thread.

Remington 700 is 1 1/16"(1.062) X 16 and will clean up just fine for small ring mausers.