• This Forum is for adults 18 years of age or over. By continuing to use this Forum you are confirming that you are 18 or older. No content shall be viewed by any person under 18 in California.

6br dies

First experience with this chambering. Suffering from information overload.

I *think* I want a bushing die. Seems to me I probably need a body die as well?

Where would you start if you were new to this chambering?

Thanks for looking.
Don't know why you would need a body die. Been reloading for my 6BR Norma since 2017. I bought a Whidden bushing die. It comes with a free bump gauge. I can send you a free fired and sized 6BR Norma case if you want to see if it chambers. If it's the older 6br Remington cartridge I would think it would be labeled Remington Arms Co. on the barrel? Almost all the competition shooters use a bushing die or a custon die made based on providing 3 fired cases. If it's an original barrel on a Rem action it's probably not a 6BR Norma?

I don't remember if 1 bushing diam comes with the Whidden die. I turn necks to 0.0125" and use a .265" bushing. .272" no turn neck. I might have a 6BR Remington case. It's bigger than a 6BR Norma.

It's not complicated. I have a minimum of tools and gadgets and I am happy with the ammo I make. Keep it simple.
 
I started working with the 6 Br about12 years ago. I started with the Forster set including a micrometer seating die and FL sizer. Based on the recommendation of an experienced shooter I went to a Redding bushing die. The problem with a bushing die is that eventually you develop Donuts. May or not be a problem based on your seating depth. If the base of the bullet is above the donut when seated. So beware of the bullet selection and throat dimension.
I don't think a bushing die has anything to do with donuts. It's brass in the shoulder area moving forward.
 
Don't know why you would need a body die. Been reloading for my 6BR Norma since 2017. I bought a Whidden bushing die. It comes with a free bump gauge. I can send you a free fired and sized 6BR Norma case if you want to see if it chambers. If it's the older 6br Remington cartridge I would think it would be labeled Remington Arms Co. on the barrel? Almost all the competition shooters use a bushing die or a custon die made based on providing 3 fired cases. If it's an original barrel on a Rem action it's probably not a 6BR Norma?

I don't remember if 1 bushing diam comes with the Whidden die. I turn necks to 0.0125" and use a .265" bushing. .272" no turn neck. I might have a 6BR Remington case. It's bigger than a 6BR Norma.

It's not complicated. I have a minimum of tools and gadgets and I am happy with the ammo I make. Keep it simple.
Used rifle. Not sure if the brass actually was fired in this chamber.
That's why.
 
I use a standard Redding die for 6br, using Alpha brass. However, I do not use the expander ball and resize, then a ,2415 mandrel ( Sinclair) to set neck tension. I seat with a Redding ordinary die with the added micrometer seater. Oddly, it's the only calibre that I do not have Wilson seating dies for. It makes extraordinary ammunition - so no need for upgrades, but I may add the Wilson seater, mainly for logistics. The BR is an easy cartridge to load for, if you take care of OAL and neck tension.

For the Alpha Dasher, I use a Wilson full length bushing die(269) - no expander ball, a 243 mandrel and Wilson seater. The 6BRX, Norma and Lapua brass and uses a Redding "S" die with a 268 bushing.
 
A good setup is either the Redding #77317 Type S full length bushing die or a Harrell's #2. Both of these will give the same amount of case sizing. The Redding is adjustable so the bushing will size more of the length of the neck, if you want it to. Wilson's full length bushing die is another one I can recommend.

For a seater, a Wilson standard inline seater works great.

Grab a small press like the RCBS Partner and a small arbor press for the Wilson seater and you have a nice, compact setup for loading at the range.
 
Used rifle. Not sure if the brass actually was fired in this chamber.
That's why.
If it chambers (without sizing), and you got it from whoever you bought the rifle from, it probably was. Use scotch tape on the case head and see if 2 or 3 plies keep the bolt from closing. If both those are successful, you'll be good to go.

In the long run, though, a couple of hundred pieces of new brass isn't all that expensive.

I'm using a Wilson neck die (arbor press type), and hit it with a Redding body-only die when the bolt starts dragging (usually every 5 or 6 firings, at which point it gets annealed, body sized, and checked for trim length.) Seating is with a Wilson arbor press inline seater.

FWIW (and to add to your confusion) Redding dies are sold as 6BR Remington. They, and others, have not changed the spec to 6BR Norma.
 
Update - I've measured the shoulder angle and it's 30° on the fired brass.
The brass will chamber, but it's REALLY tight. Definitely -0- headspace.
The case length is 1.562 give or take .001". It has a bit of room in the neck when chambered when viewed with a borescope. .471" at the base before the extractor groove. So it's a Norma chamber.1000003051.jpg
 
Last edited:

Upgrades & Donations

This Forum's expenses are primarily paid by member contributions. You can upgrade your Forum membership in seconds. Gold and Silver members get unlimited FREE classifieds for one year. Gold members can upload custom avatars.


Click Upgrade Membership Button ABOVE to get Gold or Silver Status.

You can also donate any amount, large or small, with the button below. Include your Forum Name in the PayPal Notes field.


To DONATE by CHECK, or make a recurring donation, CLICK HERE to learn how.

Forum statistics

Threads
166,904
Messages
2,225,176
Members
80,047
Latest member
Thisisdenny
Back
Top