• This Forum is for adults 18 years of age or over. By continuing to use this Forum you are confirming that you are 18 or older. No content shall be viewed by any person under 18 in California.

6.5 creed and H4350

I used up my H4895 so now onto another powder H4350. I want to challenge myself to the 1000 yard milk jug shoot. Any suggestions on component's - I already have the brass Norma LR primer and Lapua SR primer also the powder. What I need are loads for a Ruger RPR 1st gen, Vortex PST 6x24x50 FFP EBR2C Milrad reticle. What load data and bullets do you all use and or recommend. I do have a few Barnes 140 Match Burners and some 140 Hornady ELD's. So any equipment and loads will be appreciated.
Thanks
 
I used up my H4895 so now onto another powder H4350. I want to challenge myself to the 1000 yard milk jug shoot. Any suggestions on component's - I already have the brass Norma LR primer and Lapua SR primer also the powder. What I need are loads for a Ruger RPR 1st gen, Vortex PST 6x24x50 FFP EBR2C Milrad reticle. What load data and bullets do you all use and or recommend. I do have a few Barnes 140 Match Burners and some 140 Hornady ELD's. So any equipment and loads will be appreciated.
Thanks
Not real sure about his load but a close friend of mine is loading RL-19 with 140 class bullets in his 6.5 C M with great groups @ 100 yds.
 
I ran the 140 eldm s @ 2800 with H4350 was just over 42g with the Lapua spb, shot well with a 20 th jump.
Tried various powders I found around 2800 or a little more to be a good node for the 140 s in the cm @ 1000 .
 
I run h4350 in one rifle at 41.5gr with berger 140vld.
Another rifle im using r16 with 140eldm and getting 100 fps faster speeds.
Last summer I did some testing with the 140 gr bullets I had on the shelf.

All Hornady, 5 shots each with 40.5 gr, H4350, CCI #41 primers and Starline brass.
I was on the 1000 yd range that uses a doppler measurement at the target. The FPS that I observed was at the target 1000 yds away NOT at the muzzle.

140 Match - 1287 FPS AVG
140 A MAX - 1327 FPS AVG
140 ELD - 1373 FPS AVG.

I am not trying to tell you what bullet is the best as all 3 will give me a sub MOA group. Just a little higher on the target due to the increase in FPS and the B.C. G1 factor.
 
Last edited:
I recently tried some H4831SC in my creedmoor with 145g bullets and was very impressed with the velocity and accuracy.
The case is full but I’m getting 2870 FPS and tight groups from a 28” barrel.
It’s a 8 twist Bartline and it seems faster than my old barrels.
Just another option.
 
The original hornady load as printed on the box was federal 210m 41.5 gr H4350. I believe the coal was 2.820. Somewhere around there will be your most accurate load. FWIW R 26 will get you 150 fps more ball park.
 
I used up my H4895 so now onto another powder H4350. I want to challenge myself to the 1000 yard milk jug shoot. Any suggestions on component's - I already have the brass Norma LR primer and Lapua SR primer also the powder. What I need are loads for a Ruger RPR 1st gen, Vortex PST 6x24x50 FFP EBR2C Milrad reticle. What load data and bullets do you all use and or recommend. I do have a few Barnes 140 Match Burners and some 140 Hornady ELD's. So any equipment and loads will be appreciated.
Thanks

For my RPR gen 1, krieger barrel 7.5 twist:

Lapua brass
CCI 450
136 scenars
41.5 H4350
~2800 FPS

Hornady Brass
GM 210M
140 ELDs
41.2 H4350
~2700 FPS

Also, if you are using the stock trigger, you can replace it with this spring and get it to a crisp 1 lb. I prefer this spring with the stock trigger to the timney

https://www.mcarbo.com/ruger-american-rifle-trigger-spring-kit.aspx
 
Last edited:
I use 143 gr eldx and r-16 with mine and get .2” group at 200 yd if that helps. I can’t get a hold of h4350 where i live but was lucky to get r-16.
Running almost exact same load with the eldx and was sub MOA out at 375. Looking forward to trying at 700. No place around to go for 1000. Did have some good luck on calm day with the 123 Scenars at 700
 
I used up my H4895 so now onto another powder H4350. I want to challenge myself to the 1000 yard milk jug shoot. Any suggestions on component's - I already have the brass Norma LR primer and Lapua SR primer also the powder. What I need are loads for a Ruger RPR 1st gen, Vortex PST 6x24x50 FFP EBR2C Milrad reticle. What load data and bullets do you all use and or recommend. I do have a few Barnes 140 Match Burners and some 140 Hornady ELD's. So any equipment and loads will be appreciated.
Thanks
42.3gr H4350 with 140gr ELD-M, CCI 200 primer and loading .015” off the lands provided great 1000yd results in my RPR.
 

Upgrades & Donations

This Forum's expenses are primarily paid by member contributions. You can upgrade your Forum membership in seconds. Gold and Silver members get unlimited FREE classifieds for one year. Gold members can upload custom avatars.


Click Upgrade Membership Button ABOVE to get Gold or Silver Status.

You can also donate any amount, large or small, with the button below. Include your Forum Name in the PayPal Notes field.


To DONATE by CHECK, or make a recurring donation, CLICK HERE to learn how.

Forum statistics

Threads
165,170
Messages
2,190,955
Members
78,729
Latest member
Zackeryrifleman
Back
Top