fclass

  1. Which light small press for range reloading?

    I have been up in the air asking around. But wanted to get a general consensus. What is a good press for full length sizing at the range. I really want something smaller and lighter. As of right now, the only thing I can think of is the harrels compact and the rcbs partner. I wish I...

  2. Bullet seating variations for fclass or BR, whats acceptable?

    So I use a Wilson inline seating die with a hydro press. For what ever reason, I never checked my variations round to round for consistency. Don’t know why. But I got a Redding instant indicator in the mail (always wanted one) and so I measured 20 rounds for seating depth. The seating...

  3. Montour county rifles melplate uniformer review?

    Looking for reviews on the montour county Rifles melplat uniformer. I currently have the Hoover, But that little copper shard in the hollow point after trimming drives me bonkers, I would think that could deflect wind as well. Feels like it defeats the point of trimming. I see that...

  4. Where to find a lighter ejector spring?

    Was wondering where to find a lighter ejector spring for a Rpr bolt. At the moment I removed the ejector not to ruin my brass, but was hoping there was a resource to get a lighter spring so the brass will just turn out and remove by hand instead of it flying across the cement?

  5. Bullet pointing/trimming based on bullet length?

    I pre-apologize for this question. I know opinions will vary and also, because I ask a lot of bullet measuring questions. Buuttttt. , in the recesses I’d my mind a thought hit me about tipping or trimming bullets. If the lengths are not the same, they will trim or tip differently...

  6. How to use JB bore paste and Kroil correctly?

    I know they sell a kit with both included. And I also hear a lot of people on here using that combo for tough deposits. Do you only use the JB/kroil when the barrel is new?? Or once and a while down the road for deep cleanings? Or every time? I only ask because I always hear the joke...

  7. Will hydro press with neck die work?

    Will my Wilson neck die work on my 21 century hydro press?

  8. Labradar for 475. Today till 7pm pst (ebay)

    This should work. Has to be done on the ebay app. Not website. Add labradar to cart and click add coupon. “PSAVETODAY”. Says 15% off up to 100 dollars. It says it will work. With coupon it will be @475. Good luck. For today only till 7pm pacific time I believe

  9. VGA felt cleaning pellets?

    Do we like vga felt cleaning pellets?? And/or do we like using a little oversized for cleaning carbon ring? They are not cheap so I want to see if they are worth buying

  10. Technical aspect of Adams trickler system?

    I was pondering getting the Adams system. I’m not total dummy (only partial), but not a brain surgeon either or a software engineer. So how hard is it to setup and maintain? And can it be glitchy? Just kind of want a easy operation system like my charge master.

  11. Pacific super mag, 3 ram press parts?

    So I picked up this press, because I loved it on first site and thought it was the coolest thing I ever saw. But I need a few parts for it. This press is a little before my time, but not everyone’s, hehe. So wondering if anybody on here may know where to get parts, or if anybody may...

  12. Bore Tech Cu+2 Vs sweets vs wipeout.

    Hey all, I was looking to experiment with a few copper removers. I know there is a wide range of opinions. I currently use wipe out accelerator, with wipe out foam. By morning, the foam dripping out of the end of the barrel is a beautiful nuclear radiation bright blue. It never...

  13. Does auto trickle only work with fx120i?

    I was just wondering if the auto trickle system only works with the 120i scale. I have a a&d Fx700ct, which is love and is always very accurate. Was also very expensive. Is there a way to adapt to a different scale, Or software/hardware setup will be an issue?

  14. Importance of different bullet lots??

    Is it ok to mix bullet lots if you are separating by weight and bbto??? Or is there another reason not to mix lots. Just curious.

  15. 21 century lathe turning question

    So I am somewhat new to turning. And I purchased a 21 century lathe. I am sure my question apples to any lathe tho. When I feed in the brass, it cuts the brass as expected. So if I pull the brass out and send it back in, without adjusting anything, it take off more, than again, takes...

  16. Are spotting scopes necessary for benchrest?

    I was just wondering, Are spotting scopes necessary for benchrest shooting? Especially when the rifle scopes usually zoom to 60x??

  17. 300blk reload data confusion

    So just starting to reload for pistol length, 1:8 300 blkout. I have Sierra 220 smk and h110 powder. Question is if you look at the 2 uploaded images, one is Hodgdon’s, and one is Sierra. H says 9.2gr is the max load, while Sierra says 10.1-12.2. So I cannot say I’m not confused.

  18. Labradar vs Magnospeed v3

    Before I make the purchase, I was wondering if there is any significant difference between the labradar and the magnospeed v3. Saving 200. wound be nice, but want what’s best and willing to pay more to have what’s right first time around. Looking at reviews, I don’t see a much of a...

  19. Long Range Accuracy still in business?

    Does anybody know if LRA is still in business? Can’t find their website and are out of stock everywhere. Just curious

  20. Bullet comparators compared?? Reviews please

    So my reloading ocd is now in the market for a comparator. I have noticed the plain and simple ones, which I have. It’s ok. So I have noticed a few that have got my attention. First I saw the Darrell Holland gold standard comparator that kind of has the setup like a Wilson trimmer...

Upgrades & Donations

This Forum's expenses are primarily paid by member contributions. You can upgrade your Forum membership in seconds. Gold and Silver members get unlimited FREE classifieds for one year. Gold members can upload custom avatars.


Click Upgrade Membership Button ABOVE to get Gold or Silver Status.

You can also donate any amount, large or small, with the button below. Include your Forum Name in the PayPal Notes field.


To DONATE by CHECK, or make a recurring donation, CLICK HERE to learn how.

Classified Ads

Forum statistics

Threads
165,725
Messages
2,201,306
Members
79,060
Latest member
Trayarcher99

Share This Page

Back
Top