Search results

  1. What the smallest centerfire?

    Why?? what for? Bob

  2. Ok i dont understand this.. Help for .38spl load....

    Ok you guys, from a long term pistolero -- the speed of sound is greater than the speed of these bullets, the result is the sound wave is kicking off the crono, either speed them up or mover much further back from the screens. lots of experience in this and the stuff bout bullets/powder/crimp...

  3. Memorial Day - what it really it all about

    This one is special. Please put aside the day's clutter, take a moment... Absolutely one of the best tributes to our military that I've ever seen. Simply awesome... After you click on Mansions; do not click on anything else. It will start playing by itself. Sound UP! Full Screen! Thank you to...

  4. somethin weard brass and green slime

    no snert, no cat, trays on shelf 5 ft up, nothing above to drain or lead down. Bob

  5. somethin weard brass and green slime

    cant figure it our so I dumped the whole batch of brass, and the cob mixture from the vibrator. start clean, been doing this over 55 years and never had this happen, Bob

  6. somethin weard brass and green slime

    I have recently cleaning a lot of brass, some mine and some range, I sorted into trays 9mm,40,45acp, and set aside stacked on top of each other today I went back to sort some more and the top two trays, 9mm and 40sw the brass had a liquid - dark green, on the brass and settled to the bottom of...

  7. Need a gunsmith to change Remington 700 barrel...

    I have found the R. W. Hart folks in Nescopeck pa to be very good fast and above all honestly knowledgeable. they are of the Hart bbl family. Bob

  8. Refinishing wood stock

    as above, I strip, if checkered tape off the checkering the use a tooth brush to get that area clean, sand lightly to the 600 lever, then I start with a stain that gives the color level I am looking for, test area where you can re sand, in the bbl channel, and then stain the stock rubbing in a...

  9. Remingto 308 throat - yuck

    Roadkiill, you are right , however until recently they took a middle of the "road" approach and throated for the 170-80 stuff and gave a working basis for the different weights, todays looong throat have no flexibility bob

  10. Remingto 308 throat - yuck

    Settin back a couple of threads is not a bummer, as fried cases measure right on and the taper will clear up any minute differences, secondly, a good smith (Hart) with a scope and a background of MAKING barrels, can determine if the bbl is good. remember this is not a bench rest rifle or a 1000...

  11. Remingto 308 throat - yuck

    doesn't shoot worth burning powder, sending to Harts, let them scope the bbl, and if ok, true, set back a couple of threads and run a good chamber reamer in. plan is to shoot mostly the 150gr area so will throat accordingly. will keep posted. Bob

  12. Remingto 308 throat - yuck

    my son pickup up a Rem 700 in 308win with a 20" fluted bbl the Sinclair gage for checking and determining the OAL repeatedly came up with a 2.940"bolt face to bullet point using a Sierra 155 match hpbt, that just works out to the bullet base in the case mouth about .015. the jump would b e a...

  13. Joined Riverbend

    I was one of the early members, and must say you are in for a great experience, I have shot br, ipsc, skeet and trap there and just plain fun shooting. the folks are as you say, just plain good friendly and knowledgeable. Bob

  14. Rem 700 VLS 6mm Rem

    the rifle should be helped by the above suggestion to remove the pressure point from under the bbl, also the action screws, + these ideas I have found help greatly, mark the back of the locking lugs with a felt tip then close/open a number of times - remove the bolt and look at the lugs, if...

  15. 45 ACP Dies, are there pistol dies like: Forster, Wilson, Whidden etc?

    RCBS makes carbide dies that are taper crimp, I have used them on many 1000s of loads for 38/9mm/40sw/45acp and 44spcl and 44mag -they are as accurate as you can shoot. I use them on my competition ipsc, ihmsa shooting for years, and at 200 meters they offered all the accuracy you can muster. Bob

  16. Which barrel do you recommend

    I guess I am the odd ball, I had mine done by Wally/ Bobby Hart, with a 13 twist Hart 26" and it shot in the .100's so what is to complain, 55 Sierra bk at 3725. lots of pd's me their maker. bob

  17. 40SW cast bullet ??

    non rifle ? I have a Walther ppq in 40 sw, reg rifling, shoot jacked stuff great one ragged hole, I have tried the RCBS 180 cast bullet sized .401 in a Star sizer, and the thing k-holes!!!! at 15 yds in my other 40s this has never happened, tried Univ 5.1 gr got 980 fps which is not...

  18. 280 AI

    I had 2, and they are great, both 26" hart 9 twist, on 700trued,- shot in the .300's with the following, 280 ackely 700bld Hart 26" 140 SBT 3.805/3.25 9 1/2 H 4831sc 62.8 3150 5 .35" my gun H4350ext 58.6 3140 4 0.35 my gun H4350ext 58.4 3140 4 0.35 Robert's 140NBT 3.335 " " " " " " same 160SBT...

  19. Help with 40

    I have shot 1000's of cast bullets in pistol, ipsc, etc, I always taper crimp, and never had the case bulge at the bullet base - I believe you have bullets that are not properly sized, on the 40, I use 401 size die in a Star sizer, I also never used HARD cast, as they tend to cause problems...

  20. xp-100 stock

    I shot hand gun Sil of years using 2 xp 100s originally they were in mid grip one iron sight and one scope, I restocked and re bbl them to rear grip and 7br Hart bbl, the rear grip was far more accurate when shooting from position, as you could brace the fore end. I never shot possible with the...

Upgrades & Donations

This Forum's expenses are primarily paid by member contributions. You can upgrade your Forum membership in seconds. Gold and Silver members get unlimited FREE classifieds for one year. Gold members can upload custom avatars.


Click Upgrade Membership Button ABOVE to get Gold or Silver Status.

You can also donate any amount, large or small, with the button below. Include your Forum Name in the PayPal Notes field.


To DONATE by CHECK, or make a recurring donation, CLICK HERE to learn how.

Classified Ads

Forum statistics

Threads
166,964
Messages
2,225,621
Members
80,071
Latest member
GWL

Share This Page

Back
Top