Use smaller increments. I turn the tuner all the way in even if it is past the zero on the scale and start at what I call the true zero then only adjust 5 clicks at a time the reason for this if you go 25 clicks there is a good chance within those 25 clicks is the setting you are looking for.Figure I might start a dumpster fire, but would like opinions.
From left to right these are ten shot groups (2 shots then increase 25 clicks) from 0-100, 100-200, 200-300, 300-400 and 400-500. Which group would you choose to fine toluene from?
View attachment 1369946
I would most likely explore group # 4. Has less vertical and horizontal.Figure I might start a dumpster fire, but would like opinions.
From left to right these are ten shot groups (2 shots then increase 25 clicks) from 0-100, 100-200, 200-300, 300-400 and 400-500. Which group would you choose to fine toluene from?
View attachment 1369946
That is what my gut reaction is. But the fourth group which includes 2 shots at 400, 2 shots at 425, 2 at 450, 2 at 475 and 2 at 500 had the same vertical as the first and was much tighter horizontally. Of course, the method says to test at the group with the least vertical.Why would you not explore zero and 25 first if they put 4 shots into the same hole?
Lee has kind of been my mentor with regard to tuning (and lots of other stuff - he has an amazing amount of knowledge and is VERY generous in sharing it). I just put together a new RF repeater w/a Shilen "ratchet" barrel. It shot pretty good without a tuner, using a lot of Lapua CX I bought for my 1413. But I have a standard Harrel's tuner and no rifle for it, so last week I decided to put it on this new rifle. I started from "physical" zero (which actually was 5 or -20 graduations below "ruled 0"). I shot 3-shot groups and moved the tuner 5 graduation per groups. Within 5 groups, I found a "tune"! Moved up another 5 and it went away, moved back down 5 below and it went away, went back and shot 2 more groups and was extremely pleased.Use smaller increments. I turn the tuner all the way in even if it is past the zero on the scale and start at what I call the true zero then only adjust 5 clicks at a time the reason for this if you go 25 clicks there is a good chance within those 25 clicks is the setting you are looking for.
Lee
Neat point. The target was not perfectly plumb. I normally level the target but did not yesterday.Kind of an obvious question, but did you check the target alignment with a level before shooting? 1, 2, and 4 are fairly close in apparent vertical spread, but if the targets were not perfectly plumb, the order between them could change.
[QUOTE
I have tried the "Hopewell" method and think it is a total waste of ammo and time!
So as you move your tuner you will see the poi move up and down and your looking for the best high group? How many shot per setting and how many clicks between settings on the tuner?I wouldn't argue in that you will find a decent tune in about every revolution of a Harrell's tuner. The question is it the best one. Thats where its worth doing .
Admittedly, I don't use it either. We all have our preferences as to where we like to "live" with it. Lee likes them light & has said he liked at least in the past to be on the low end of the tuner. I like them between 150-200. You see some incredible shooting rifles with all kinds of crap screwed onto them.
Bottom line, you can find a tune at many different settings.
I mentioned above the sine wave thing I did earlier this year. I'll never try tuning a rifle again without doing it as I think since I've done my rifles more consistent. I believe in the past I've seen small groups & thought it was a good tune but not at the top of the swing. I'm comfortable moving my tuner in the past & since I've done that test I haven't needed to touch it again & have been more consistent each outing. Just sayin'
[QUOTE
I have tried the "Hopewell" method and think it is a total waste of ammo and time!