Will I need to bush firing pin , rem 700 if I go 6x47 L?

[DHD]

Are the aftermarket bolts such as a Pacific Tool & Gauge built to tolerances that eliminate the need to go through this pin hole bushing process? Is this why people install aftermarket bolts?

Thanks,
Trevor

I believe you have to order the bolt w/the small pin from PT&G. I would imagine people use the aftermarket bolts for many reasons not just the small pin. Larger/smaller BF, larger OD, different bolt knob/handle, destroyed old bolt, etc.....

You may as well get the small pin when you get another bolt. I really can't see a downside for not using the small pin when you are starting fresh.

 

[Erik Cortina]

Are the aftermarket bolts such as a Pacific Tool & Gauge built to tolerances that eliminate the need to go through this pin hole bushing process? Is this why people install aftermarket bolts?

Thanks,
Trevor

The main reason people use PT&G bolts is because of the options.
If you wanted to Bush the bolt, flute it, install a Sako extractor, and bush the firing pin, you will be better off just ordering a new bolt. Bushing the bolt itself is the biggest reason to order a new bolt.

All the things mentioned above can be done to a Remington 700 bolt, but it takes more time and money.

 

[Hengehold]

Are the aftermarket bolts such as a Pacific Tool & Gauge built to tolerances that eliminate the need to go through this pin hole bushing process? Is this why people install aftermarket bolts?

Thanks,
Trevor

The main reason people use PT&G bolts is because of the options.
If you wanted to Bush the bolt, flute it, install a Sako extractor, and bush the firing pin, you will be better off just ordering a new bolt. Bushing the bolt itself is the biggest reason to order a new bolt.

All the things mentioned above can be done to a Remington 700 bolt, but it takes more time and money.

Thanks for the info. I am unfamiliar with "bushing the bolt" that you mentioned. What does it mean to bush the bolt and when would it be appropriate?

Thanks,
Trevor

 

[Erik Cortina]

Are the aftermarket bolts such as a Pacific Tool & Gauge built to tolerances that eliminate the need to go through this pin hole bushing process? Is this why people install aftermarket bolts?

Thanks,
Trevor

The main reason people use PT&G bolts is because of the options.
If you wanted to Bush the bolt, flute it, install a Sako extractor, and bush the firing pin, you will be better off just ordering a new bolt. Bushing the bolt itself is the biggest reason to order a new bolt.

All the things mentioned above can be done to a Remington 700 bolt, but it takes more time and money.

Thanks for the info. I am unfamiliar with "bushing the bolt" that you mentioned. What does it mean to bush the bolt and when would it be appropriate?

Thanks,
Trevor

Remington bolts have a generous clearance between bolt and bolt bore. If you open the bolt halfway and wiggle the back of it there will be some side play because of it. When you bush the bolt, it makes the bolt act as if it was bigger in diameter thus reducing the amount of side play. Bushing the bolt is mainly done when using the action for BR shooting or any other discipline that requires a very tight action. Bushing the bolt is not recommended for tactical or hunting used due to the likelihood of debris locking up the bolt of it gets lodged between bolt and action.

 

[jrm850]

Remington bolts have a generous clearance between bolt and bolt bore. If you open the bolt halfway and wiggle the back of it there will be some side play because of it. When you bush the bolt, it makes the bolt act as if it was bigger in diameter thus reducing the amount of side play. Bushing the bolt is mainly done when using the action for BR shooting or any other discipline that requires a very tight action. Bushing the bolt is not recommended for tactical or hunting used due to the likelihood of debris locking up the bolt of it gets lodged between bolt and action.

I think I remember reading that you are a fan of Borden actions... I made some bolt bushings in the Borden spirit that so far seem to be doing everything right. Tight at lockup but enough clearance for debris.

Edit: forgot that the main point was to show Hengehold an example of bushing a bolt.

 

[carlsbad]

Are the aftermarket bolts such as a Pacific Tool & Gauge built to tolerances that eliminate the need to go through this pin hole bushing process? Is this why people install aftermarket bolts?

Thanks,
Trevor

The main reason people use PT&G bolts is because of the options.
If you wanted to Bush the bolt, flute it, install a Sako extractor, and bush the firing pin, you will be better off just ordering a new bolt. Bushing the bolt itself is the biggest reason to order a new bolt.

All the things mentioned above can be done to a Remington 700 bolt, but it takes more time and money.

But a reason not to change the bolt is that the headspace is likely to need adjustment. If you're changing barrels, it makes sense to replace the bolt. If not, it makes sense to bush the firing pin. --Jerry

 

[22DASHER]

Perfect timing.... Pierced my first primer with a mild load in my 22 Dasher today. First one and hopefully it will be the last because the bolt is now getting shipped off.