SELLING Upgrade for AMP Mate to improve feeding

[F Class John]

This is a replacement part for the AMP Mate that improves feeding and virtually eliminates any partial feeds or stuck cases associated with the ‘delrin push feed’ mechanism. Historically the AMP Mate allowed four or more cases to be in the vertical feed tube which led to extra weight pushing down on the white delrin feed block. In some cases, this extra weight prevented the cases from being pushed completely into the shell holder leading to jams, double feeds and other issues. This replacement part lowers the case feeder and cuts the numbers of cases in the vertical column by roughly half, allowing the feed block to move under far less weight and friction.

Fits up to any case with a .535 base (most of your magnums) and maintains the same case height as the original part. Based on testing, if the height fit before, it’ll fit with this.

You will have to physically lower your case feeder so make sure your stand is capable of being made shorter.

AMP Mate Feeder Upgrade — F Class John

This is a replacement part for the AMP Mate that improves feeding and virtually eliminates any partial feeds or stuck cases associated with the ‘delrin push feed’ mechanism. Historically the AMP Mate allowed four or more cases to be in the vertical feed tube which led to extra weight pushing down on

www.fclassjohn.com

 

[Alantra]

Are you saying I can do away with the auxiliary tube that came in different sizes?

 

[F Class John]

Are you saying I can do away with the auxiliary tube that came in different sizes?

For most standard sizes yes. I've only tested up to 300wsm and similar magnum cases and it comes with an insert for smaller sizes .223 and down.

 

[Macka86]

This works great I have one and it allows everything to feed a lot smoother!!! Well worth it!

 

[Alantra]

Ok, sold to the New England Cajun. Along with 2 of the humidity caps.

Thank you!

 

[Flea21]

This is a replacement part for the AMP Mate that improves feeding and virtually eliminates any partial feeds or stuck cases associated with the ‘delrin push feed’ mechanism. Historically the AMP Mate allowed four or more cases to be in the vertical feed tube which led to extra weight pushing down on the white delrin feed block. In some cases, this extra weight prevented the cases from being pushed completely into the shell holder leading to jams, double feeds and other issues. This replacement part lowers the case feeder and cuts the numbers of cases in the vertical column by roughly half, allowing the feed block to move under far less weight and friction.

Fits up to any case with a .535 base (most of your magnums) and maintains the same case height as the original part. Based on testing, if the height fit before, it’ll fit with this.

You will have to physically lower your case feeder so make sure your stand is capable of being made shorter.

AMP Mate Feeder Upgrade — F Class John

This is a replacement part for the AMP Mate that improves feeding and virtually eliminates any partial feeds or stuck cases associated with the ‘delrin push feed’ mechanism. Historically the AMP Mate allowed four or more cases to be in the vertical feed tube which led to extra weight pushing down on

www.fclassjohn.com

So this replaces the three clear ones that come with the amp mate? Like an all in one basically? I’m definitely interested just need some clarity on its function.. please elaborate or maybe make a video like you usually do.

 

[F Class John]

Yes it replaces the three pieces and while I haven't been able to check every single cartridge, I know it'll handle at least up to 300wsm and 7prc and down to just about anything the old part handled. There's an insert for smaller cartridges .223 and down that fits into the adapter. This unit effectively lowers the feed height by at least two pieces of brass so you will need to be able to lower your case feeder to accommodate and then your case feeder will clip directly to the part. The reduction in brass in the tube lower the friction applied to the delrin block which allows it to feed largely without issue (I say largely because I can't guarantee it but everyone who's tried one so far hasn't had a failure to feed). Until I get a better video made here's a couple to look at.

 

[Flea21]

Yes it replaces the three pieces and while I haven't been able to check every single cartridge, I know it'll handle at least up to 300wsm and 7prc and down to just about anything the old part handled. There's an insert for smaller cartridges .223 and down that fits into the adapter. This unit effectively lowers the feed height by at least two pieces of brass so you will need to be able to lower your case feeder to accommodate and then your case feeder will clip directly to the part. The reduction in brass in the tube lower the friction applied to the delrin block which allows it to feed largely without issue (I say largely because I can't guarantee it but everyone who's tried one so far hasn't had a failure to feed). Until I get a better video made here's a couple to look at.

Sweet! Thanks for the follow up and clarification. I haven’t had a cycling issue with mine but I don’t like changing everything out from magnum to standard and back. I’ll definitely get one of these for that alone… Thank You.

 

[F Class John]

Sweet! Thanks for the follow up and clarification. I haven’t had a cycling issue with mine but I don’t like changing everything out from magnum to standard and back. I’ll definitely get one of these for that alone… Thank You.

Keep in mind you'll still have to adjust the piece up or down potentially from larger to smaller sized brass.

 

[Flea21]

Keep in mind you'll still have to adjust the piece up or down potentially from larger to smaller sized brass.

Oh yea, for sure but at least rolling doesn’t need to be swapped out beyond just a shell holder.

 

[Alantra]

I’m hoping this fixes my feeding issues. I’m struggling with the feeding or the ejector. I can get one to work but I can’t keep both working consistently.