• This Forum is for adults 18 years of age or over. By continuing to use this Forum you are confirming that you are 18 or older. No content shall be viewed by any person under 18 in California.

Reprograming RCBS chargemaster 1500

When I first discovered I had problems with my chargemaster I watched a whole bunch of videos and on one of them the content provider mentioned that on of the guys that was tinkering with chargemasters had a list of all the different functions that could be changed and had provided that list to others. I am having a heck of a time finding it. Could anyone here point me in the right direction? thanks Mark
 
When I first discovered I had problems with my chargemaster I watched a whole bunch of videos and on one of them the content provider mentioned that on of the guys that was tinkering with chargemasters had a list of all the different functions that could be changed and had provided that list to others. I am having a heck of a time finding it. Could anyone here point me in the right direction? thanks Mark
RCBS will send you the info. If you ask. Tommy Mc
 
Instructions provided by RCBS around 4/2/11 for Chargemaster 1500 Speed Adjustment:



1. Turn the Chargemaster 1500 unit on.

2. When 0.0 gn is on the display, press BOTH the ENTER and the EDIT MEM keys on the

dispenser at the same time. Hold for a second and then release. If done properly ADJUST

PARAMETERS should scroll across the display followed by HSP_A1 00015.68 (This number

represents the number of grains away from your entered charge when the tube will shift

from fast speed to medium speed. That is at 15.68 gn from your target charge the

dispenser will shift from fast to medium speed.) To speed up the unit, this number needs to

be decreased, and to slow down the unit, this number needs to be increased. (On a slow

unit, I would change this number to 11.00 gn this is done by pressing the following keys: 1

1 0 0 ENTER (pressing the enter key sets that value and moves to next setting in program

in this case, to medium speed to slow speed setting)

3. HSP_B1 00003.42 should scroll across the display now. This number represents where

the unit will shift from medium to slow speed. Use the same process as in step 2 to enter

updated values. For a slow unit I would change this number to 2.50 gn this is done by

pressing the following keys: 2 5 0 ENTER (pressing the enter key sets that value and moves

to the next setting in the program. In this case, the slow speed to trickle speed transition)

4. HSP_C1 00001.08 should now scroll across the screen. This number represents where the unit will shift from slow speed to trickle. Use the same process as before to enter the value. For a slow unit I would change this number to .90 gn. This is done by pressing the following keys: 9 0 ENTER

5. This is all the adjustment that needs to be done to the unit. You then need to press the

ENTER key to cycle through the rest of the program without changing any of the values

(approx. 22 times). Once complete, the unit will start its normal initial countdown process.

Next, test the dispenser by entering a target charge (i.e. 44.5 ENTER, and pressing DISP).

Disregard the first charge and throw a few charges at these settings to see if they satisfy

your needs. If not, return to step 2 and repeat the process to program in different values.



Due to powder grain size variations, you may have to adjust the unit for each different powder used.



Here is another full list of parameters, accessed sequentially by pressing



"EDIT MEMORY" and "ENTER" simultaneously, and then pressing "ENTER" to advance through the list. This list includes the original factory setting for reference.



To change a parameter, type the new number once the old number is displayed. Record all factory data

first because there is no "FACTORY RESET" available. * marks parameters used in the above notes. (XXX)

indicates my factory data.

*HSB_A1 (15.68) Grains under target weight to go from full to high speed for low weight

*HSB_B1 (3.42) Grains under target weight to go from high to slow speed low weight

HSP_C1 (1.08) Grains under target weight to go from slow to final trickle speed low weight

*MSP_A2 (39.20) Grains under target weight to go from full to high speed for medium weight

*MSP_B2 (8.55) Grains under target weight to go from high to slow speed medium weight

MSP_C2 (2.25) Grains under target weight to go from slow to final trickle speed medium weight

*SSP_A3 (196.00) Grains under target weight to go from full to high speed for heavy weight

*SSP_B3 (42.75) Grains under target weight to go from high to slow speed heavy weight

SSP_C3 (11.32) Grains under target weight to go from slow to final trickle speed heavy weight

SEL (065) ???

*F_A (050) Grains for a Heavy Charge

*M_A (035) Grains for a Medium charge

*S_A (006) Grains for a slow charge

*W_F (200) Rotation for Full speed

*W_M (100) Rotation for Medium speed

W_S (036) Rotation for slowest speed

*S_F (012) Scale sensitivity timeout time in m/s fast speed

S_M (024) Scale sensitivity timeout time in m/s medium speed

S_S (128) Scale sensitivity timeout time in m/s slow speed.

FR1 (040) ?

FS1 (016) ?

FR2 (080) ?

SR1 (032) ?

SS1 (008) ?

SR2 (040) ?

DEC (000) ?

AT (000) ?
 

Upgrades & Donations

This Forum's expenses are primarily paid by member contributions. You can upgrade your Forum membership in seconds. Gold and Silver members get unlimited FREE classifieds for one year. Gold members can upload custom avatars.


Click Upgrade Membership Button ABOVE to get Gold or Silver Status.

You can also donate any amount, large or small, with the button below. Include your Forum Name in the PayPal Notes field.


To DONATE by CHECK, or make a recurring donation, CLICK HERE to learn how.

Forum statistics

Threads
165,788
Messages
2,203,382
Members
79,110
Latest member
miles813
Back
Top