• This Forum is for adults 18 years of age or over. By continuing to use this Forum you are confirming that you are 18 or older. No content shall be viewed by any person under 18 in California.

Film Dipping a Scope

I have a Vortex scope that is going on a Rem 700 SA, using the Mag-Pul 700 stock.

My plan is to cera-kote the metal in Desert Tan, and film dip the stock and scope.

Issue: how have you gentlemen accomplished this without covering all the markings on the scope with the film dip? It does not have screw on lens covers, or turret caps to seal.

thanks,

Rich
 
I have a Vortex scope that is going on a Rem 700 SA, using the Mag-Pul 700 stock.

My plan is to cera-kote the metal in Desert Tan, and film dip the stock and scope.

Issue: how have you gentlemen accomplished this without covering all the markings on the scope with the film dip? It does not have screw on lens covers, or turret caps to seal.

thanks,

Rich
Better hope the o rings are good. Larry
 
I have a Vortex scope that is going on a Rem 700 SA, using the Mag-Pul 700 stock.

My plan is to cera-kote the metal in Desert Tan, and film dip the stock and scope.

Issue: how have you gentlemen accomplished this without covering all the markings on the scope with the film dip? It does not have screw on lens covers, or turret caps to seal.

thanks,

Rich
I would look on you tube for a video. They have videos of everything. Matt
 
I'm doing the exact same thing very soon. Spoke to the dealer doing it and they want to know if the scope is sealed so as not to be affected by water. They cover the lenses and markings and dip the scope. My response was no it will not leak. I called sightron and they assured me of it leaks, it's covered completely. I'm sure most scopes would be. The 50.00 to dip it would be minor.
 
I cover them with blue painters tape, spray with Duracoat, then Hydro dip. Peel off the tape just as if you had had painted it. When you peel the tape off, pull it in a direction away from the dip so you are not lifting the dip away from the surface, more like folding the tape back on itself.

Edit
Maybe call Vortex and ask but I would think it's covered unless they consider it "working" on the scope or something.
 
I cover them with blue painters tape, spray with Duracoat, then Hydro dip. Peel off the tape just as if you had had painted it. When you peel the tape off, pull it in a direction away from the dip so you are not lifting the dip away from the surface, more like folding the tape back on itself.

Edit
Maybe call Vortex and ask but I would think it's covered unless they consider it "working" on the scope or something.
I'm certainly inexperienced at this process but wouldn't think the scope would be submersed in the water very long. I quick dip is safe for most scopes I would think.
 
I'm certainly inexperienced at this process but wouldn't think the scope would be submersed in the water very long. I quick dip is safe for most scopes I would think.
If I was going to try it the water would have to be warmer then the scope. The expansion of the air inside the scope should oust the water out. If the water was cooler it would suck it in. Larry
 
If I was going to try it the water would have to be warmer then the scope. The expansion of the air inside the scope should oust the water out. If the water was cooler it would suck it in. Larry
Again not sure if it's a cold water or warm water Dip process. Mine will be going in soon. I'll know more afterwards. Someone said that cerakote is a process that's done on scopes as well. Apparently after shooting the coat of paint on the scope, it's put into an oven at a much lower temp but for much longer as to not negatively affect any seals or plastic parts. Not sure if that sounds like the best plan.
 
I would appreciate it if you would report back about a week after...
;)
Spoke to the owner of camo Creek hydrographics where I'm getting my scope and stock dipped. I only want a solid color on my scope. He does not have solid colors, only camo patterns or patterned dips. He suggests duracoat for my scope. It takes from 7-10 days to completely cure but it's virtually the same as cerakote after curing. Not quite as durable but on a scope I'm not as concerned. Sounds like that's my route. Actually a less expensive option. Think shops are getting 50.00 for a tactical/target type scope. I will do this project myself.
 
I think Midway is the cheapest place to get Duracoat, other places charge a ton for shipping/hazmat.
 
I used blue painters tape and a razor blade. stuffed objectives with foam, taped the ends and all numbers, model, serial# as well as turrets (but I guess I should have just taken them off) duracoat paint, let dry, then dipped. Rings, mounts, scope all done same way and done separately.

557053_623344487700520_728054552_n.jpg
 
Interesting response. There is an article here by a member recommending Hydro-Dip company in Meridian, ID.

I emailed them about doing my scope and synthetic rifle stock.
$100 to dip my scope, and I have to sign a waiver absolving them of any liability if anything happens to the scope.
Is this common?

Rich
 
Interesting response. There is an article here by a member recommending Hydro-Dip company in Meridian, ID.

I emailed them about doing my scope and synthetic rifle stock.
$100 to dip my scope, and I have to sign a waiver absolving them of any liability if anything happens to the scope.
Is this common?

Rich
Not for me I wouldn't have it done. Larry
 

Upgrades & Donations

This Forum's expenses are primarily paid by member contributions. You can upgrade your Forum membership in seconds. Gold and Silver members get unlimited FREE classifieds for one year. Gold members can upload custom avatars.


Click Upgrade Membership Button ABOVE to get Gold or Silver Status.

You can also donate any amount, large or small, with the button below. Include your Forum Name in the PayPal Notes field.


To DONATE by CHECK, or make a recurring donation, CLICK HERE to learn how.

Forum statistics

Threads
165,852
Messages
2,204,895
Members
79,174
Latest member
kit10n
Back
Top