F-CLASS / BENCH REST STOCKS

Jason Avila

Gold $$ Contributor
Did someone say stocks? Yup. Quick story, for the last few years I have been working on designing and manufacturing the finest built rifle stocks possible. After some ups and downs I took the plunge and and tooled up with some of the best equipment possible to manufacture them.
I will start by posting this beautiful laminated stock. 36” long, 2.950 wide forend, 8” long bag rider, butt parallel to forend. Ready for inletting and a top coat. $550 plus shipping. IMG_7102.jpegIMG_7101.jpegIMG_7100.jpegIMG_7105.jpegIMG_7104.jpegIMG_7103.jpeg
 
Jason Avila said:
Did someone say stocks? Yup. Quick story, for the last few years I have been working on designing and manufacturing the finest built rifle stocks possible. After some ups and downs I took the plunge and and tooled up with some of the best equipment possible to manufacture them.
I will start by posting this beautiful laminated stock. 36” long, 2.950 wide forend, 8” long bag rider, butt parallel to forend. Ready for inletting and a top coat. $550 plus shipping. View attachment 1447927View attachment 1447928View attachment 1447929View attachment 1447930View attachment 1447931View attachment 1447932
Click to expand...
Is it possible to get this without the cooling ports in the for end ?
 
Jason Avila said:
Did someone say stocks? Yup. Quick story, for the last few years I have been working on designing and manufacturing the finest built rifle stocks possible. After some ups and downs I took the plunge and and tooled up with some of the best equipment possible to manufacture them.
I will start by posting this beautiful laminated stock. 36” long, 2.950 wide forend, 8” long bag rider, butt parallel to forend. Ready for inletting and a top coat. $550 plus shipping. View attachment 1447927View attachment 1447928View attachment 1447929View attachment 1447930View attachment 1447931View attachment 1447932
Click to expand...
How do I go about ordering one of these.Thanks...Jim Miller
 
Jason Avila said:
Did someone say stocks? Yup. Quick story, for the last few years I have been working on designing and manufacturing the finest built rifle stocks possible. After some ups and downs I took the plunge and and tooled up with some of the best equipment possible to manufacture them.
I will start by posting this beautiful laminated stock. 36” long, 2.950 wide forend, 8” long bag rider, butt parallel to forend. Ready for inletting and a top coat. $550 plus shipping. View attachment 1447927View attachment 1447928View attachment 1447929View attachment 1447930View attachment 1447931View attachment 1447932
Click to expand...
It's nice to see the laminations run dead straight.
I worked on a bargain stock for my son in law with crooked laminations,it sucked.
It's hard to do a good job working with crap.
He thougt the stock turned out great. I can see the crooked lines every time I see that rifle.

Hal
 
Jason Avila said:
Yes. I won’t do a full inlet for clones unless i physically have that action or a 3D model of it, you would more than likely have to finish the bolt handle, ejection ports and blend tang area.
Click to expand...
I had that very same question. I'll be PMing you in the near future.
 
If you can produce a prone rifle stock for center fire long range I’d be interested (i.e. McMillan, Robertson or A.Sitman configuration).
 
You must log in or register to reply here.

Upgrades & Donations

This Forum's expenses are primarily paid by member contributions. You can upgrade your Forum membership in seconds. Gold and Silver members get unlimited FREE classifieds for one year. Gold members can upload custom avatars.


Click Upgrade Membership Button ABOVE to get Gold or Silver Status.

You can also donate any amount, large or small, with the button below. Include your Forum Name in the PayPal Notes field.


To DONATE by CHECK, or make a recurring donation, CLICK HERE to learn how.

Classified Ads

Forum statistics

Threads
165,901
Messages
2,206,073
Members
79,207
Latest member
bbkersch

Share This Page

Back
Top