• This Forum is for adults 18 years of age or over. By continuing to use this Forum you are confirming that you are 18 or older. No content shall be viewed by any person under 18 in California.

.223 bushing ?

Gman

Gold $$ Contributor
Would someone Please measure the neck "outside diameter" of a loaded .223 round using new Lapua brass with a 69 grain Sierra Match King. I need to order a couple of Wilson bushings & don't have the bullets or brass yet. Thank You !!!
 
Would someone Please measure the neck "outside diameter" of a loaded .223 round using new Lapua brass with a 69 grain Sierra Match King.
I'm sure you know this, but the loaded neck OD isn't going to be any difference (to speak of) if it is a 69 gr Sierra Match King, or a Berger 80.5 gr bullet. Less than 0.0005" at most.

I load for a Krieger 223 barrel and use current production Lapua brass. My loaded neck OD runs .2490" no matter what bullet I use. My fired neck OD is 0.2505 to 0.2510". And before seating my sized neck OD is 0.2475".
 
I have 500 rounds of loaded Lapua factory ammo and the ones I checked are .250 or .2505 on the neck OD unfired.

In my Criterion, fired cases come out .2545. My Forster is honed at .245 and gives sized necks just under .247 depending on neck hardness.

I honed this die for the thinnest brass I have, which has loaded diameters around .2485.
 
I would suggest buying several bushings within a likely diameter window. That way, you'll have the correct bushing.

I have run a .223 in F-TR for years and always used a 0.248" bushing with Lapua brass (un-turned necks). A 0.248 bushing gives me between .0015" and .0020" neck tension (interference fit), whereas a 0.249" bushing would be at .001" or under. Even subtle differences in technique, setup, and measuring equipment can generate variance of half a thousandth to one thousandth in these measurements, so there is no way to be sure exactly what you need based on numbers provided at an internet shooting forum. Consider these numbers a "guide" only; something that will get you to the correct general area. However, you'll still need to determine actual measurements and the proper bushing size needed for your specific setup.

I would therefore recommend getting yourself a set of something like 0.249", 0.248", 0.247", and maybe even 0.246" steel bushings. They're relatively inexpensive and once you have determined the best bushing size for your setup, you can always go back and buy just a single bushing of that size in the more costly titanium nitride if you wish. FWIW - I ended up using the smaller bushings that I initially bought but did not use loading for an AR with a different and less expensive brand of brass (i.e. slightly thinner neck walls), so purchasing the extra sizes was not "wasted" money.
 
I would suggest buying several bushings within a likely diameter window. That way, you'll have the correct bushing.

I have run a .223 in F-TR for years and always used a 0.248" bushing with Lapua brass (un-turned necks). A 0.248 bushing gives me between .0015" and .0020" neck tension (interference fit), whereas a 0.249" bushing would be at .001" or under. Even subtle differences in technique, setup, and measuring equipment can generate variance of half a thousandth to one thousandth in these measurements, so there is no way to be sure exactly what you need based on numbers provided at an internet shooting forum. Consider these numbers a "guide" only; something that will get you to the correct general area. However, you'll still need to determine actual measurements and the proper bushing size needed for your specific setup.

I would therefore recommend getting yourself a set of something like 0.249", 0.248", 0.247", and maybe even 0.246" steel bushings. They're relatively inexpensive and once you have determined the best bushing size for your setup, you can always go back and buy just a single bushing of that size in the more costly titanium nitride if you wish. FWIW - I ended up using the smaller bushings that I initially bought but did not use loading for an AR with a different and less expensive brand of brass (i.e. slightly thinner neck walls), so purchasing the extra sizes was not "wasted" money.
Plus most calipers are only accurate to plus or minus .001 anyway
 

Upgrades & Donations

This Forum's expenses are primarily paid by member contributions. You can upgrade your Forum membership in seconds. Gold and Silver members get unlimited FREE classifieds for one year. Gold members can upload custom avatars.


Click Upgrade Membership Button ABOVE to get Gold or Silver Status.

You can also donate any amount, large or small, with the button below. Include your Forum Name in the PayPal Notes field.


To DONATE by CHECK, or make a recurring donation, CLICK HERE to learn how.

Forum statistics

Threads
166,325
Messages
2,216,626
Members
79,554
Latest member
GerSteve
Back
Top