SELLING 21'st Century Neck Turning Lathe A la carte

jepp2

Gold $$ Contributor
Somehow I have accumulated an excess of the 21'st Century Neck Turning lathes and parts. My experience has been, that folks sell what they needed, and rarely is that what the buyer needs. So I intend to offer options on what you want, and you only buy what is needed for your neck turning needs. Everything I am offering is in excellent condition with very little use.

The basic neck turning lathe WITHOUT turning tool holder (red object on the left) and shell holder/driver (silver on the right side). I offer this for $115 shipped TYD. Why would someone need this? Maybe they are turning by hand without the lathe currently, or they have 2 setups and only 1 lathe, and don't want to switch back and forth? You can buy this from 21'st Century for $199 + tax + shipping.

Lathe Base.jpg

I have some turning tool holders available. If you buy them with the lathe they run $90 additional. I have the following cutters (you only select 1) to choose from: 20, 23, 25, 30, 35 and 40 degree. That will give you the red part of the lathe with the large X on it.

I also have some shell holder/driver combinations available. Those run $35 if purchased with the lathe. That is the right side X on the picture above. Your choice of 2-2, 2-BR, 3-3, and 4-4. These fit:
2-2 is the large rifle primed 308 bolt case head family
2-BR is the small rifle primed 308 bolt case head family
3-3 is the large rifle primed 30-30 case head family
4-4 is the small rifle primed 223 bolt case head

If you find I have the lathe with the turning holder (and cutter) and shell holder/driver you need, total cost is $240 shipped. Or if you buy that from 21'st Century it will be $401.50 + tax if applicable.

I also have once completely new lathe, still in the factory packaging from 21'st Century. It has the 30 degree cutter and 2-BR shell holder driver. This one is $280 shipped and it has pictures in a separate listing. Perfect for 6 and 6.5 CM as well as many other cartridges. SOLD

I have some mandrels excess as well and a couple of mandrel dies. Prices if purchased with the above:
- die with lock ring $35
- Nitride mandrel $25 (only in 30 cal)
- TiN mandrel $15
- SS mandrel $7.50
- Solid Carbide $35

If you aren't sure what angle cutter you need, or shell holder/driver for you cartridge you can either refer to the 21'st Century chart attached, or just send me a PM.
 

Attachments

Last edited:
ill let you tell me what i need, or you have, 6 creedmoor, 6xc small primers, 30br, maybe 223, 6mm-223
 
Somehow I have accumulated an excess of the 21'st Century Neck Turning lathes and parts. My experience has been, that folks sell what they needed, and rarely is that what the buyer needs. So I intend to offer options on what you want, and you only buy what is needed for your neck turning needs. Everything I am offering is in excellent condition with very little use.

The basic neck turning lathe WITHOUT turning tool holder (red object on the left) and shell holder/driver (silver on the right side). I offer this for $115 shipped TYD. Why would someone need this? Maybe they are turning by hand without the lathe currently, or they have 2 setups and only 1 lathe, and don't want to switch back and forth? You can buy this from 21'st Century for $199 + tax + shipping.

View attachment 1530815

I have some turning tool holders available. If you buy them with the lathe they run $90 additional. I have the following cutters (you only select 1) to choose from: 20, 23, 25, 30, 35 and 40 degree. That will give you the red part of the lathe with the large X on it.

I also have some shell holder/driver combinations available. Those run $35 if purchased with the lathe. That is the right side X on the picture above. Your choice of 2-2, 2-BR, PPC-PPC, 3-3, and 5-5.

If you find I have the lathe with the turning holder (and cutter) and shell holder/driver you need, total cost is $240 shipped. Or if you buy that from 21'st Century it will be $401.50 + tax if applicable.

I have some mandrels excess as well and a couple of mandrel dies. Prices if purchased with the above:
- die with lock ring $35
- Nitride mandrel $25 (only in 30 cal)
- TiN mandrel $15
- SS mandrel $7.50
- Solid Carbide $35

If you aren't sure what angle cutter you need, or shell holder/driver for you cartridge you can either refer to the 21'st Century chart attached, or just send me a PM.
Do you have a spare motor setup?
 

Upgrades & Donations

This Forum's expenses are primarily paid by member contributions. You can upgrade your Forum membership in seconds. Gold and Silver members get unlimited FREE classifieds for one year. Gold members can upload custom avatars.


Click Upgrade Membership Button ABOVE to get Gold or Silver Status.

You can also donate any amount, large or small, with the button below. Include your Forum Name in the PayPal Notes field.


To DONATE by CHECK, or make a recurring donation, CLICK HERE to learn how.

Forum statistics

Threads
165,860
Messages
2,205,008
Members
79,175
Latest member
rlk99
Back
Top