• This Forum is for adults 18 years of age or over. By continuing to use this Forum you are confirming that you are 18 or older. No content shall be viewed by any person under 18 in California.

Inch pound tool

kochie said:
What a good inch pound tool to install my scope scope ring bases & scope rings .
Click to expand...
Toss the torque wrench for scope rings. I kinked a scope tube using "proper" ring torque. Now I am sitting here waiting on the first post mentioning that I confused 16 to 25 inch lbs. with ft. lbs........

Danny
 
Last edited:
I’ll put another vote in for the Borka wrench. I was torn between buying it and the fix it sticks.

The fix it sticks get expensive quick if you want the limiter drives that give positive feedback when you get to the desired setting. The variable fix it stick tool is a lot more economical, but you have to watch the dial as you get close to desired torque.

The Borka system cams over when you get to the desired setting. It comes with a large variety of bits and a nice carrying case.
 
I like my Wheeler Fat Wrench, but I've never tried anything else. So my suggestion would be the Wheeler scope mounting kit - has a fat wrench, bits, bar stock for lapping rings and lining up rings, lapping compound, and scope bubble levels. All in a nice case to keep everything together.
 
This is what I use for scope bases and scope ring cap screws, it takes a hex bit driver holder and is adjustable. It is in Nm instead of inch lbs but it comes with a conversion chart and is simple to use, you set the torque setting with on the back of the handle with the supplied Allen key. It's a click style. https://www.amazon.com/Felo-0715752...prefix=felo+torque+handle,aps,277&sr=8-3&th=1

I use an In Lbs wrench on the ring side nuts.
 
The Wiha torque driver is one of the best I've used. They also have kits with multiple bits.

Fix-it sticks or the NF tool kit work fine in the field. Their torque limiters come in pre-set weights or are adjustable (15-65 and 6-25 inch-pounds).
The Nightforce scope mounting tool kit has a 2-10 inch-pound driver, ratchet handle, bits and Borka torque limiters in 25, 68 and 100 inch-pounds.
 
wheeler fat wrench. Comes with bits and works as well as I need it to. fits easily in the range bag and is easy on the pocketbook. I actually found a brand new one at a flea market for 10 bucks, so now I have two!

However, i have always eyed those fix it sticks. I just don't see what I would gain by spending that much more. If I am within +/-1.5 inch lbs, that's good enough for me.
 
Dimner said:
wheeler fat wrench. Comes with bits and works as well as I need it to. fits easily in the range bag and is easy on the pocketbook. I actually found a brand new one at a flea market for 10 bucks, so now I have two!

However, i have always eyed those fix it sticks. I just don't see what I would gain by spending that much more. If I am within +/-1.5 inch lbs, that's good enough for me.
Click to expand...
Ok thanks guys all good information
 
Probably the "Fat" dude does the job just as good as the FixIt stix that looks sexier.

I have Wiha and Fat wrench. Both work as promised.
 
Emmett Dibble said:
Any reasonably priced torque screw driver that goes from about 5-40 inch pounds. Should cover all ring/base/action screw needs. You don't need scientific/certified but you don't want to cheap out either. If you aren't use to tightening up small torques it is VERY easy to over tighten things. I have a Tohnichi 50RTD-A that I have had for YEARS....
Click to expand...
Ok
 
I used the Wheeler fat wrench for years, then had a guy I trust tell me the torque value isn’t always what you think it is. I still have it and use it , that and fix it sticks. Both of those products are handy if you want to take it to the range or out in the field in case you have an issue. Nothing worse than being on a hunt and have something losses up. Most of my stuff is properly torqued but I have helped quite a few friends and family during hunts.

I’ve been using a CDI 1/4” torque now when I’m home for the most part, I can’t remember the range of torque but it’s not terribly big and covers what I need for gun related jobs. I trust it more. Overkill? Maybe
 
I use this digital torque screwdriver I bought on Amazon. It has worked exceptionally well me me.

VEVOR Digital Torque Screwdriver, 1/4" Drive Screwdriver Torque Wrench, Electrician Torque Screwdriver with LCD, 2.65-70.67 in-lbs Torque Range, 0.01 N.m Increment Torque Screwdriver with Bits & Case​

B0CC236LT8

Tim
 
TIMO said:
I use this digital torque screwdriver I bought on Amazon. It has worked exceptionally well me me.

VEVOR Digital Torque Screwdriver, 1/4" Drive Screwdriver Torque Wrench, Electrician Torque Screwdriver with LCD, 2.65-70.67 in-lbs Torque Range, 0.01 N.m Increment Torque Screwdriver with Bits & Case​

B0CC236LT8

Tim
Click to expand...
. Ok thanks again
 
You must log in or register to reply here.

Upgrades & Donations

This Forum's expenses are primarily paid by member contributions. You can upgrade your Forum membership in seconds. Gold and Silver members get unlimited FREE classifieds for one year. Gold members can upload custom avatars.


Click Upgrade Membership Button ABOVE to get Gold or Silver Status.

You can also donate any amount, large or small, with the button below. Include your Forum Name in the PayPal Notes field.


To DONATE by CHECK, or make a recurring donation, CLICK HERE to learn how.

Classified Ads

Forum statistics

Threads
165,326
Messages
2,193,219
Members
78,819
Latest member
DJT

Share This Page

Back
Top