Brass or Aluminum reducing inserts for Chargemaster

Discussion in 'Tools, Dies, Rests, Reloading Components & Misc' started by MDM, May 31, 2014.

Trader History (72)
  1. Richard Andrews

    Richard Andrews

    Joined:
    Aug 13, 2014
    Messages:
    3
     
  2. Richard Andrews

    Richard Andrews

    Joined:
    Aug 13, 2014
    Messages:
    3
    I would like to order two of the brass inserts with the added alum. added. please respond email bruce@featherrods.com with total price and address where to remit cost. by the way I ordered a couple of the older model inserts a few years ago and they work fine. hope the new ones are even better.
    thanks
    Bruce
     
  3. MDM

    MDM Silver $$ Contributor

    Joined:
    Apr 25, 2010
    Messages:
    303
    I have more ready to go.
     
  4. HomeSlice

    HomeSlice

    Joined:
    Sep 3, 2009
    Messages:
    105
    I'd like one please
     
  5. gilmillan1

    gilmillan1

    Joined:
    Jul 4, 2014
    Messages:
    390
    I would like a set of the two inserts. How do i pay and whats the total?
     
  6. MDM

    MDM Silver $$ Contributor

    Joined:
    Apr 25, 2010
    Messages:
    303
    PM sent. Yes, still making these. Thanks
     
  7. foxguy

    foxguy Gold $$ Contributor

    Joined:
    Jul 26, 2012
    Messages:
    356
    Chargemaster reducing inserts use and powder clearing question.

    Hi, I have ordered and received the 2 piece inserts. They work do work very well.
    I load using Varget, H4895, and a few others.

    After powder charging the cases I always clear the powder used out of the Chargemaster with the reducing bushing in place it makes impossible to clear all of the powder out of the dispensing tube in the RCBS recommended way. I have resorted to removing the bushing every time and with the tape used to hold the bushing in place the tape gets buggered up after a few times.

    Have you found a good way to accomplish the removal of all of the powder from the RCBS 1500 without having to remove the bushing?
     
  8. ronsroom1

    ronsroom1 Silver $$ Contributor

    Joined:
    Mar 11, 2008
    Messages:
    240
    Would like 1 of each.
    Ron
     
  9. HomeSlice

    HomeSlice

    Joined:
    Sep 3, 2009
    Messages:
    105
    Mine arrived a couple of days ago. Previously I has been getting roughly 1/5 overthrows with Varget. Tonight I ran 50 through with the reducer installed and didn't have a single miss. My chargemaster is much more usable now.

    Thanks so much for making this thing and sending me one. I couldn't be happier.
     
  10. ronsroom1

    ronsroom1 Silver $$ Contributor

    Joined:
    Mar 11, 2008
    Messages:
    240
    Mine arrived several days ago.
    Should have bought these a long time ago.
    Thanks, Ron
     
  11. riverwolf1

    riverwolf1 Silver $$ Contributor

    Joined:
    Feb 2, 2008
    Messages:
    467
    I would like 1 brass sleeve .308 and the smaller sleeve. Pm me as to where to send the money too.
    Thx
    Gary Vanlier
     
  12. Globalstar66

    Globalstar66

    Joined:
    Feb 2, 2017
    Messages:
    1
    I just sent you a PM for one of these sets.... Thanks, Robbie.
     
  13. MDM

    MDM Silver $$ Contributor

    Joined:
    Apr 25, 2010
    Messages:
    303
    I leave my inserts in the chargemaster. bump the trickle button until the open slot on the tube inside the hopper is facing down. Pick up the whole unit and tilt it backwards so the powder goes back in the hopper. Rocking it back and forth a little, then empty the hopper back into the powder jug. Then, I tilt the unit clear forward to see if anything comes out of the tube and catch it in the pan.
     
  14. kerjo

    kerjo Silver $$ Contributor

    Joined:
    Mar 11, 2005
    Messages:
    50
    I put money in your PayPal account using PayPal friends. Did you receive it?
    kerjo
     
  15. MDM

    MDM Silver $$ Contributor

    Joined:
    Apr 25, 2010
    Messages:
    303
    Yes. Still waiting on your shipping address. This is the 4th time I've asked for it. Don't make me use my google-fu to find you. Lol. Check your messages man. :)
     
    Last edited: Feb 10, 2017
  16. MDM

    MDM Silver $$ Contributor

    Joined:
    Apr 25, 2010
    Messages:
    303
    Bump
     
  17. jp

    jp Gold $$ Contributor

    Joined:
    Jun 23, 2008
    Messages:
    283
    let me measure mine and I will order one
     
  18. jp

    jp Gold $$ Contributor

    Joined:
    Jun 23, 2008
    Messages:
    283
    I need one brass .310 with the aluminum insert pm me your payment info thx
     
    Last edited: Mar 4, 2017
  19. rinoray

    rinoray Silver $$ Contributor

    Joined:
    Jan 14, 2005
    Messages:
    211
    I've had mine for a few weeks and have loaded several rounds of 223, 308, & 6BR with Varget, XBR, and H4895 and what a great addition to my Chargemaster. Speeds things up and consistent accuracy. Great product!
    [​IMG]
     
  20. andy 2

    andy 2

    Joined:
    Oct 7, 2015
    Messages:
    5
    I would like a brass one with small insert. Dia is .310 e-mail atddad@att.net phone 440 478 6973 THANK YOU
     

Share This Page