tclaunch's Recent Activity

  1. tclaunch replied to the thread WANTED lee auto prime lever.

    As the above poster asked if you tried the new square tray handle on the round priming tool? It fits!

    Dec 11, 2017 at 8:50 AM
  2. tclaunch liked d1686's post in the thread December 9, 17 Big Piney's 600 Yd F Class Houston, Mo Match Results.

    Thanks everyone for coming out and battling the cold wind to shoot with us. We had two shooters from TN. and one shooter from IA. this...

    Dec 11, 2017 at 7:25 AM
  3. tclaunch liked Dusty Stevens's post in the thread At what RPM are you threading barrels ?.

    i love a middle back gear speed. i only thread faster when im on the shine to calm my nerves

    Dec 10, 2017 at 11:13 AM
  4. tclaunch liked GenePoole's post in the thread At what RPM are you threading barrels ?.

    I run about 100-150 rpm. This is attained with VFD at 20 Hz or so using the lowest non back-gear setting on a South Bend 13. I use...

    Dec 10, 2017 at 11:12 AM
  5. tclaunch liked urbanrifleman's post in the thread 6mmx47 lapua .100 thousands short 40° shoulder.

    This looks like a great design.

    Dec 7, 2017 at 2:30 PM
  6. tclaunch liked Stan Taylor's post in the thread 6mmx47 lapua .100 thousands short 40° shoulder.

    Yes I intend to as soon as I get some.

    Dec 7, 2017 at 2:30 PM
  7. tclaunch liked urbanrifleman's post in the thread 6mmx47 lapua .100 thousands short 40° shoulder.

    Oh man... I bet that kills... You should try R16. :)

    Dec 7, 2017 at 2:30 PM
  8. tclaunch liked Stan Taylor's post in the thread 6mmx47 lapua .100 thousands short 40° shoulder.

    Yes sir you are pretty much on point the h 4350 is about 37.8 grains at 3030 fps easy on case's.

    Dec 7, 2017 at 2:30 PM
  9. tclaunch liked urbanrifleman's post in the thread 6mmx47 lapua .100 thousands short 40° shoulder.

    So I am just asking. Is your cartridge the same shoulder and neck length as the 6bra? Which would be a 6BR neck length with a 40...

    Dec 7, 2017 at 2:30 PM
  10. tclaunch replied to the thread Picture Test.

    Yes, that appears to be what I bought.

    Dec 6, 2017 at 10:42 AM
  11. tclaunch replied to the thread Picture Test.

    Try a light squirt of WD40 and fine (purple) scotch brite to add that sheen. I have an antique SB H10L lathe and believe I am threading...

    Dec 6, 2017 at 7:53 AM
  12. tclaunch liked Riesel's post in the thread Picture Test.

    My hat is off to you Sir! Try as I might, I can't get those threads to be that smooth. I'm using the Arthur Warne thread cutting set up...

    Dec 6, 2017 at 7:48 AM
  13. tclaunch liked Stan Taylor's post in the thread Picture Test.

    Nice tool Tim thanks for the heads up on it first Set of threads once got it set right wasn't as pretty a thread as yours but no taper...

    Dec 6, 2017 at 7:32 AM
  14. tclaunch liked Cigarcop's post in the thread Picture Test.

    Nice job Tim!

    Dec 6, 2017 at 7:31 AM
  15. tclaunch liked Hal's post in the thread Picture Test.

    Very nice. What type of cutter and cutting oil are you using ? Hal

    Dec 6, 2017 at 7:31 AM